LightSpeed Technologies Delta X10 - Manual (Page 20)

min max dB dB - 40 0 – +
0
LOW – +
0
HIGH
TONE CONTROL LEVEL LINE/CD VOICE OVER MUSIC LINE
MASTER
VOLUME BATTERY
STATUS
I N
O
U
T
MIC 1 MIC 2
min max
min max
LEVEL
LEVEL
LOW CUT
LIMIT
music speech
IN
min max
LEVEL LOW CUT
music speech
IN
LOW OK WIRELESS MIC 1
LOW CUT
music speech
WIRELESS MIC 2
LOW CUT
music speech
ON MUTE
EXTERNAL
SPEAKER A
SWITCHED
8 OHM
EXTERNAL
SPEAKER B
8 OHM
CHARGING STATUS LightSPEED
MADE IN EUROPE EXTERNAL POWER SOURCE
MAINS
12VDC /4A
AC 90-264V
47-63Hz
FUSE T2A
POWER
ON
OFF
MUTE
DO NOT OPEN THE COVER. REFER SERVICING TO QUALIFIED PERSONNEL. REPLACE FUSE ONLY WITH THE SAME TYPE AND RATING.
ACTIVE
LINK
GND + 12V
4 1 2 3
Wireless
Sound System
WIRELESS MIC 1 WIRELESS MIC 2
CD-ROM ART GOES HERE NO diSC
STOP PLAY/PAUSE A — B REPEAT
SCAN/SEARCH — SKIP — EJECT
PROG
LightSPEED 7100R UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ RF CHANNEL
LightSPEED 7100R UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ RF CHANNEL
VOL
Max PWR Min
VOL
Max PWR Min
Delta X10
ON MUTE
EXTERNAL
SPEAKER A
SWITCHED
8 OHM
EXTERNAL
SPEAKER B
8 OHM
CHARGING STATUS LightSPEED
MADE IN EUROPE EXTERNAL
POWER
SOURCE
MAINS
12VDC /4A
AC
90-264V
47-63Hz
FUSE
T2A
POWER
ON
DO NOT OPEN
THE COVER.
REFER SERVICING
TO QUALIFIED
ACTIVE
LINK
GND
+ 12V
4 1
2 3
2
Volume
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ RF
CHANNEL
VOL
Max PWR Min
3
Frequency Group
4
5
SCAN
Manual Channel
Select Buttons
1
LightSPEED Technologies • Wireless Sound Solutions • Toll Free: 1-800-840-3662
18
Wireless Receiver(s)
Operating Instructions LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ RF
CHANNEL
VOL
Max PWR Min
DET DET DET DET DETAILED OPERA AILED OPERA AILED OPERA AILED OPERA AILED OPERATION - WIRELESS RECEIVER TION - WIRELESS RECEIVER TION - WIRELESS RECEIVER TION - WIRELESS RECEIVER TION - WIRELESS RECEIVER
Power up the Delta X system and wireless receiver(s) Power up the Delta X system and wireless receiver(s) Power up the Delta X system and wireless receiver(s) Power up the Delta X system and wireless receiver(s) Power up the Delta X system and wireless receiver(s)
1. 1. 1. 1. 1. POWER: POWER: POWER: POWER: POWER: Push the POWER switch on the base unit back panel to the ON (or MUTE) position.
2. 2. 2. 2. 2. ON LED: ON LED: ON LED: ON LED: ON LED: The ON LED will light.
3. 3. 3. 3. 3. Receiver V Receiver V Receiver V Receiver V Receiver Volume: olume: olume: olume: olume: Rotate the Power/Volume knob on the receiver module clockwise to turn on. Leave the volume at a low
level for now.
4. 4. 4. 4. 4. Frequency Group: Frequency Group: Frequency Group: Frequency Group: Frequency Group: When the receiver power is first switched on, the frequency group of the receiver will be shown briefly
as letters on the LED display.
(See frequency group chart on page 30)
Channel Selection - Wireless Receiver Channel Selection - Wireless Receiver Channel Selection - Wireless Receiver Channel Selection - Wireless Receiver Channel Selection - Wireless Receiver
Each receiver has 100 user-selectable channels to choose from. You can select a channel either manually or by pressing the
SCAN button which will automatically select a clear channel.
5. 5. 5. 5. 5. Clear Channel Scan (Recommended): Clear Channel Scan (Recommended): Clear Channel Scan (Recommended): Clear Channel Scan (Recommended): Clear Channel Scan (Recommended): Make sure the transmitter(s) is OFF before pressing this button. When this button
is pressed, the receiver will cycle through all 100 channels and select a clear frequency (this process takes about 20
seconds). Once the receiver selects the clear channel, you will need to select the same channel on the corresponding
transmitter (handheld or belt-pack).
If Y If Y If Y If Y If You Have a Second Receiver (WIRELESS MIC 2): ou Have a Second Receiver (WIRELESS MIC 2): ou Have a Second Receiver (WIRELESS MIC 2): ou Have a Second Receiver (WIRELESS MIC 2): ou Have a Second Receiver (WIRELESS MIC 2): Verify that WIRELESS MIC 1 is operating on a clear channel, and the
transmitter for WIRELESS MIC 1 is turned ON. Make sure the transmitter for WIRELESS MIC 2 is turned OFF, and then press the
“SCAN” button on the WIRELESS MIC 2 receiver. After the WIRELESS MIC 2 receiver selects a clear channel, set the WIRELESS
MIC 2 transmitter (handheld or belt-pack) to the selected channel.