Pump packages & expansion tank - options, Figure 8 pump package, Figure 9 pump mounting – Liebert EMERSON 60 HZ User Manual
Page 17: Notes, Figure 10 expansion tank, Expansion tank- (p/n 1c16717p1), Table 8 pump data, Figure 11 pump curve, 60 hz, Ackages, Xpansion
13
P
UMP
P
ACKAGES
& E
XPANSION
T
ANK
- O
PTIONS
Figure 8
Pump package
Figure 9
Pump mounting
Notes
1. Single pump packages are
17-1/4" (438.2mm) wide. Dual
pump packages are 32-1/4"
(819.2mm) wide.
2. Mounting holes are 15-11/32"
(389.7mm) apart on single
pump packages and
30-11/32" (770.7mm) apart on
dual pump packages.
3. 7-1/2hp dimensions not
shown—consult factory.
Provided on dual
pump package only
Pump suction
connections
Pump
discharge
connections
30-1/4"
(768.4mm)
See
Note 1
19"
(483mm)
See
Note
Pump Package
Mounting
1/2" (12.7mm)
diameter holes
23"
(584.2mm)
3/4"
(19.1mm)
3-1/2"
(88.9mm)
Figure 10 Expansion tank
Expansion Tank- (P/N 1C16717P1)
This tank, included in a standard pump package, has an internal volume of 8.8 gal. (33 l)
and a maximum pressure of 100 psi (690 kPa).
This tank is sized for a typical “open” system with a fluid volume of less than 75 gal.
(280l). When used in a “closed” system, volumes of up to 140 gal. (910l) can be accommo-
dated. The use of a safety relief valve, field supplied, is recommended for systems
“closed” to atmospheric venting. Other piping accessories for filling, venting, or adjusting
the fluid in the system, are recommended, but not included.
Figure 11 Pump curve, 60 Hz
Table 8
Pump data
Pump
Model
Connections
HP
Electric @ 60Hz
NPT
Suction
Female
Discharge
PH
208
FLA
230
FLA
460
FLA
575
FLA
3/4
1-1/4"
3/4"
3/4
1
7.6
6.9
N/A
N/A
3/4
1-1/4"
3/4"
3/4
3
3.5
3.2
1.6
1.3
1-1/2
1-1/4"
3/4"
1-1/2
3
6.6
6.0
3.0
2.4
2
1-1/4"
3/4"
2
3
7.5
6.8
3.4
2.7
3
1-1/2"
1"
3
3
10.6
9.6
4.8
3.9
5
1-1/2"
1-1/4"
5
3
16.7
15.2
7.6
6.1
7-1/2
3"
3"
7-1/2
3
24.2
22.0
11.0
9.0
To Calculate Total Pump and Drycooler Full Load Amps (FLA):
Total FLA = Pump FLA + Drycooler FLA
To Calculate Total Pump and Drycooler Wire Size Amps (WSA)
Total WSA = Largest Motor FLA x 1.25 + Sum of other Motor FLA values
To Calculate Total Pump and Drycooler Maximum Overcurrent Protective Device (OPD)
Total OPD = Largest Motor FLA x 4.0 + Sum of other Motor FLA values
Select standard fuse size (15A, 20A, 25A, 30A, etc.)
0
10 20 30 40 50 60 70 80 120 160 200 250 300 400
20
100
40
60
80
120
160
140
180
Flow Rate - GPM
To
ta
l Hea
d
-
ft
. w
ater