Lenoxx Electronics CD-160 - Manual (Page 9)

ANTENNAS ANTENNAS ANTENNAS ANTENNAS ANTENNAS
The built-in AM Antenna and the FM Telescoping Antenna are directional. You may find
that you can improve AM reception by rotating the set or bringing it closer to a window. The
FM Band can be adjusted by FM Telescoping Antenna. Be sure to extend the FM Telescoping
Antenna carefully to its full length for best reception.
TTTTTO LISTEN T O LISTEN T O LISTEN T O LISTEN T O LISTEN TO PRESET O PRESET O PRESET O PRESET O PRESET MEMOR MEMOR MEMOR MEMOR MEMORY YY Y Y ST ST ST ST STA AA A ATIONS (after you TIONS (after you TIONS (after you TIONS (after you TIONS (after you
programmed them) programmed them) programmed them) programmed them) programmed them)
1. Press the Power Switch ON, the Power/Batt. Lamp will light.
2. Press the Radio Switch, the Radio Indicator will light.
3. Press the Band Switch to select the band you want (AM or FM).
4. Press the Radio Presets Button to select the stations stored (01-10). You will receive
the station you stored into that preset memory. Pressing the button several times will
give you the different preset stations you stored into the preset memories 1 to 10
(Example: Pressing the button 3 times will give you Preset Number 3, press the button
4 times will give you Preset Number 4). Word “ PRESET
” and Preset Number will show in
the Display.
5. To shut off the radio, press the Power Switch again, the Power/Batt. Lamp will go off.
RADIO OPERA RADIO OPERA RADIO OPERA RADIO OPERA RADIO OPERATION TION TION TION TION
TTTTTO PLA O PLA O PLA O PLA O PLAY YY Y Y THE RADIO THE RADIO THE RADIO THE RADIO THE RADIO
PRESETTING ST PRESETTING ST PRESETTING ST PRESETTING ST PRESETTING STA AA A ATIONS TIONS TIONS TIONS TIONS
UP UP UP UP UP T T T T TO 10 AM AND 10 FM ST O 10 AM AND 10 FM ST O 10 AM AND 10 FM ST O 10 AM AND 10 FM ST O 10 AM AND 10 FM STA AA A ATIONS CAN BE ST TIONS CAN BE ST TIONS CAN BE ST TIONS CAN BE ST TIONS CAN BE STORED INT ORED INT ORED INT ORED INT ORED INTO THE PRESET O THE PRESET O THE PRESET O THE PRESET O THE PRESET
MEMORIES. (THEY MEMORIES. (THEY MEMORIES. (THEY MEMORIES. (THEY MEMORIES. (THEY WILL WILL WILL WILL WILL REMAIN IN MEMOR REMAIN IN MEMOR REMAIN IN MEMOR REMAIN IN MEMOR REMAIN IN MEMORY YY Y Y AS LONG AS THE BA AS LONG AS THE BA AS LONG AS THE BA AS LONG AS THE BA AS LONG AS THE BATTERIES TTERIES TTERIES TTERIES TTERIES
ARE INST ARE INST ARE INST ARE INST ARE INSTALLED, OR AC POWER CORD IS CONNECTED.) ALLED, OR AC POWER CORD IS CONNECTED.) ALLED, OR AC POWER CORD IS CONNECTED.) ALLED, OR AC POWER CORD IS CONNECTED.) ALLED, OR AC POWER CORD IS CONNECTED.)
1 . Press the Band Switch to select AM or FM band, and
press the Tuning or Button to select a station.
2. Press the Radio Store (Program) Button, “ PROGRAM
”
will flash in the Display.
PRESET PROGRAM
Make sure the speakers are connected (speaker wires plugged into the jacks in the back
of the set).
3. While the “ PROGRAM
” is blinking, press the Radio Presets Button to choose a memory
location (01-10). (Example: Push the Radio Presets Button 3 times for Preset Number 3;
4 times for Preset Number 4.)
4. Press the Radio Store (Program) Button again to confirm. The station now broadcasting
is stored into that preset memory.
NOTE NOTE NOTE NOTE NOTE: Steps 2-4 should be done quickly.
5. Repeat the above steps 1 to 4 to store other 9 stations into memory.
6. Each memory location (01-10) can store 2 stations, one for AM, the other for FM.
N O T E : N O T E : N O T E : N O T E : N O T E : Before you disconnect the power (AC and Battery) of the set, make sure the
Power Switch is OFF, then you have approximately 30 seconds to re-connect
the power. Otherwise, the memories may be lost and need to be re-programmed.
1. Press the Power Switch ON (the Power Lamp will light).
2. Press the Radio Switch ON (the Radio Indicator will light).
8
3. Press the AM/FM Band Switch to select the desired wave band.
4. Tune to desired station by pressing the Tuning
or Button. Each time the
button is pressed, the frequency changes.
5. To search for a station quickly (automatic tuning), keep the Tuning or Button
pressed until the station starts to change rapidly, then release the Button and it will stop
at the next strong station.
6. If you tune into a FM stereo station, “
” will
show in the Display.
7. Adjust the Volume Control to your listening preference.
8. If you prefer more bass, slide the Bass Boost Switch to ON position.
9. To turn off the radio, press the Power Switch again, the Power Lamp will go off.
CD-160S050699 V.2 E