Video config, Main menu, Continued) – Panasonic BT-LH1700WP User Manual
Page 16
16
The underlined values are factory preset setting values.
*1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not
reflected in the sub window.
*2 When “RGB-COMP.” is selected in “YP
B
P
R
/RGB” in the “INPUT SELECT” menu (
J page 21), this does not operate.
*3 The following sharpness values can each be set,
1) VIDEO system input line (VIDEO,Y/C)(Factory settings are SHARPNESS MODE : LOW,
SHARPNESS H/V : 0)
2) any other input line’s HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0)
3) any other input line’s SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0)
and the setting values for the selected input signal from within this group is displayed. The adjustment status is
displayed in the bottom right when selected.
*4 When “VAR1”, “VAR2” or “VAR3” is selected, the monitor switches to WB adjustment mode (
J page 17).
*5 When selecting USER0–63
1) Push [ENTER] (USER changes to blue).
2) Select 0–63 with [
,
], and push [ENTER].
VIDEO CONFIG
Sub menu
Settings
Explanation
GAMMA
SELECT
*2
<NORMAL>
<FILM>
*1
Used to select the gamma curve.
When FILM is selected,
mark is displayed in the top
left of the screen.
FILM GAMMA
*2
<VARICAM>
<OTHER>
Used to select the type of FILM gamma mode.
<VARICAM> VARICAM use
<OTHER>
When using other types than VARICAM
COLOR TEMP.
<USER0–63>
*5
<D93>
<D65>
<D56>
<VAR1>
<VAR2>
<VAR3>
Used to select the color temperature.
<USER0–63>
Adjustable settings 0–63 (color temperature
around 3000K–9300K)
<D93>
Color temperature around 9300K
<D65>
Color temperature around 6500K
<D56>
Color temperature around 5600K
<VAR1>
WB adjustment mode
*4
<VAR2>
WB adjustment mode
*4
<VAR3>
WB adjustment mode
*4
SHARPNESS
MODE
*2
<HIGH>
*3
<LOW>
Used to select the width of the sharpness edge.
<HIGH>
Thin edge
<LOW>
Thick edge
SHARPNESS H
*2
<0–30>
*3
Used to set the sharpness in the horizontal direction.
When adjusting, the item display moves to the lower part of the
screen.
SHARPNESS V
*2
<0–30>
*3
Used to set the sharpness in the vertical direction.
When adjusting, the item display moves to the lower part of the
screen.
I-P MODE
*2
<MODE2>
<MODE1>
Used to set the mode for IP change.
<MODE2>
Within Field
<MODE1>
Normal mode
MONO
*2
<OFF>
<ON>
Used to switch between color and monochrome (MONO).
<OFF> Color
<ON>
Monochrome
* When this is ON, the picture adjusting knob [CHROMA] setting
is fixed at 0.
ANAMO
*2
<OFF>
<ON>
If an Anamo lens has been used on the camera, and input through
SDI 720/60P, 59.94P, the picture is resized to Anamo size
magnification. (a vertically compressed signal can be amplified
vertically and corrected when it is displayed.)
SD ASPECT
*2
<4:3>
<16:9>
Used for setting the aspect ratio settings when using SD signal
input.
<4:3>
4:3 display
<16:9>
16:9 display
SCAN
*2
<NORMAL>
<UNDER>
Used to set under-scan and normal display.
<NORMAL>Normal display
<UNDER>Under-scan
NOISE WIPE
*2
<OFF>
<ON>
<OFF> This makes a fluid and smooth contrast obtainable.
This is especially effective for continuously changing the contrast
of the source signal or CG signal when the S/N is very high.
<ON>
Noise reduction mode. Depending on the camera, this mode
can be especially effective for dark scenes. We recommend
leaving this setting “ON” under normal conditions.
Main Menu
(continued)