Panasonic DMP-BD35 - Manual (Page 31)

31
RQT9248
Card Page
Network
Other difficulties with playback
When other Panasonic products respond to this remote control
Change the remote control code on the main unit and the remote control (the two must match) if you place other Panasonic products close
together.
The capacity of the SD card
decreased. ≥When a BD-Video that supports the virtual package is used, and an SD card is in the slot,
data may be written to the SD card. Erase the data by using “BD-Video Data Erase”, format
the card or use a new card.
15
MPEG-2 motion pictures and
music on an SD card cannot be
played. ≥Data that can be played from an SD card are AVCHD and JPEG data. 5
The contents of the card
cannot be read. ≥The card is not compatible or the contents on the card may be damaged.
≥Turn off and then turn on the unit again.
5
—
I can’t connect to the network. ≥Has the LAN cable come unplugged? Check that the LAN cable is properly connected.
≥Have you plugged in a modular cable for use with a telephone into the LAN terminal on this
unit? Connect with a straight LAN cable.
≥Is the power for the modem or broadband router turned on? Turn the power on for each
device.
≥Is there a mistake in the network settings? Follow any instructions you may have received
from your ISP (Internet Service Provider) and make changes to the settings.
≥Are the broadband router settings correct? Read the operating instructions for the broadband
router.
≥Is the broadband router and/or modem correctly connected? Check the operating
instructions for each device and connect accordingly.
≥Check the “Network Settings” and “BD-Live Internet Access” settings.
8
8
—
—
—
—
24, 27
While using my PC, I cannot
connect to the network. ≥Does your Internet Service Provider (ISP) or service contract prevent multiple terminals
connecting at the same time? Check the content of your contract.
—
Audio and video momentarily
pause. ≥This occurs between playlist chapters or scenes ([AVCHD]).
≥When playing a title recorded on both layers, the unit automatically switches between layers
and plays the title in the same way as a normal program. However, video and audio may
momentarily cut out when the unit is switching layers.
—
—
BD-Video or DVD-Video is not
played. ≥Ensure the disc is for the correct BD-Video region code or DVD-Video region number, and is
not defective.
≥You have set a ratings level to limit BD-Video or DVD-Video play. Change this setting.
≥Some BD-Video can only be output with HDMI.
Cover
24
—
Picture-in-picture is not played
with BD-Video. ≥Confirm whether the disc supports picture-in-picture. —
The virtual package is not
played with BD-Video. ≥Confirm whether the disc supports the virtual package.
≥The inserted SD card does not have sufficient available capacity.
≥The SD card is write-protected.
≥Sub contents copied to an SD card are provided by the disc producer as a part of the
BD-Video content. Even if you record images and audio onto an SD card, it cannot be played
as a virtual package.
15
—
5
15
Alternative soundtrack and
subtitles cannot be selected. ≥The languages are not recorded on the disc.
≥You may not be able to use the on-screen menu to change the soundtrack and subtitles on
some discs. Use the disc’s menus to make changes.
—
13
No subtitles. ≥Subtitles are not recorded on the disc.
≥Turn the subtitles on. Set “Subtitle” on the on-screen menu to “On”.
—
22
Angle cannot be changed. ≥Angles can only be changed during scenes where different angles are recorded. —
The resume play function does
not work. ≥Memorized positions are canceled when
– pressing [ ∫] several times.
– opening the disc tray.
≥The resume play function may not work depending on the disc.
≥[BD-V]: On BD-Video discs including BD-J, the resume play function does not work.
—
—
—
1 Press [SETUP].
2 Press [
3, 4] to select “General” and press [OK].
3 Press [ 3, 4] to select “Remote Control” and
press [OK].
4 Press [ 3, 4] to select the code (1, 2, or 3) and
press [OK].
5 To change the code on the remote control
While pressing [OK], press and hold the
numbered button ([1], [2] or [3]) for more than
5 seconds.
6 Press [OK].
NOTE
When the following indicator
appears on the unit’s display and
you are unable to operate the unit
The unit’s remote control code
Press and hold [OK] and the
indicated number button at the same
time for more than 5 seconds.
Set Code 1
Set Code 2
Set Code 3
Remote Control
Press [ ] and [ OK ] together
for more than 5 seconds on
the remote.
Ref
e
rence
DMP-BD35GT&GN-RQT9256_eng.book 31 ページ ２００８年９月２４日 水曜日 午後５時５分