Panasonic CQ-VD7001U - Manual (Page 23)

44 43
44 45 CQ-VD7001U CQ-VD7001U
Settings
(continued)
English English
[MENU] [MODE] []] [[] [}] [{] [ENTER]
: Previous menu
: Previous menu
: Quit
: Quit
: Select/adjust
: Select/adjust : Determine [MENU] [MODE] []] [[] [}] [{] [ENTER]
: Previous menu
: Previous menu
: Quit
: Quit
: Select/adjust
: Select/adjust : Determine
LPF/HPF (Low Pass Filter/High Pass Filter)
Cut off frequency
: down, : up
Setting range: - (in 5 Hz step)
default:
: down, : up
Setting range: , - (in 5 Hz step)
default:
Note:
¡This setting is not available if
(SRS setting) is
set to (on).
¡ (High pass filter) is enabled only on the
front speakers (R/L) and rear speakers (L/R).
HPF CUT OFF
ON
CS Auto
OFF
225 Hz 90 Hz OFF
[ ]
(High Pass Filter) HPF CUT OFF
100 Hz
160 Hz 60 Hz
[ ]
(Sub-woofer Low Pass Filter) LPF CUT OFF
SP LEVEL (Speaker level)
Adjusting the output balance of each speaker
: down, : up
: down, : up
: down, : up
: down, : up
: down, : up
: down, : up
Setting range: –10 dB to +10 dB (1 dB steps)
Default: ± 0 dB for all speakers
A test signal (a continuous tone) is output from each
speaker for approximately 2 seconds.
Adjust the output balance so that the tone appears to have
the same volume from each speaker.
Adjusting the output balance:
Adjust the volume of all of the other speakers to the volume
level of the speaker from which the test signal appears to be
the quietest.
¡If the speaker setting is
(none) or (no) for a
speaker, the test signal is not output and that speaker
cannot be selected.
¡Turn rotary volume controller or press [}] or [{]
( VOL) to adjust the volume of the test signal.
NO NONE
[ ]
(Subwoofer speaker output bal-
ance)
SUB - W
[ ]
(Left surround speaker output
balance)
L ¡ SURROUND
[ ]
(Right surround speaker output
balance)
R ¡ SURROUND
[ ]
(Right front speaker output bal-
ance)
FRONT R
[ ]
(Center speaker output balance) CENTER
[ ]
(Left front speaker output bal-
ance)
FRONT L
SP SETUP (Speaker set up)
Setting the absence/presence and size of each speaker
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
: for small speakers, or when bass playback is
not possible
default: LARGE
SMALL
LARGE
(Front speaker setting) FRONT
: when using a subwoofer
: when not using a subwoofer
default:
* A subwoofer (option, CJ-HD302 recommended) is
required. A power amplifier (option) is also required for
connecting a subwoofer.
NO
NO
YES
(Subwoofer speaker setting) SUB - W
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
: for small speakers, or when bass playback is
not possible
: when not using a center speaker
default:
* A center speaker (option, EAB-CF2 recommended) is
required.
NONE
NONE
SMALL
LARGE
(Center speaker setting) CENTER
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
: for small speakers, or when bass playback is
not possible
: when not using a surround speaker
default: LARGE
NONE
SMALL
LARGE
(Surround speaker setting) SURROUND
(AUDIO continued)
Note:
¡While the private mode is active, only
can be
adjusted.
FRONT
Note:
¡While the private
mode is active, only
and
can be
adjusted.
FRONT R
FRONT L
SP DELAY (Speaker delay)
Adjusting the timing with which the audio from each speak-
er reaches the listener’s position
: down, : up
Setting range: 0 ms to 5 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
: down, : up
Setting range: 0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
¡Make this adjustment while listening to sound.
¡If the speaker setting is
(none) for a speaker, that
speaker cannot be selected.
¡When “PRO LOGIC” is displayed, 15 ms are automatically
added to the delay time setting for the surround speakers.
NONE
[ ]
(Surround speaker delay time
setting)
SURROUND
[ ]
(Center speaker delay time set-
ting)
CENTER
MODE LEVEL
Setting the VTR/AUX input level
Make this setting if it is not possible to adjust the volume
through the connected device (on the output side).
: sets the level low/sound volume increases
: sets the level high/sound volume decreases
default:
: sets the level low/sound volume increases
: sets the level high/sound volume decreases
Note:
¡If the input level from VTR/AUX is too high, the audio will
not be output normally.
¡After setting the input level
The volume can be adjusted by pressing [}] or [{]
(VOL) on the remote control or turning rotary volume
controller on the unit.
default: HIGH
HIGH
LOW
(Setting for AUX) AUX LEVEL
HIGH
HIGH
LOW
(Setting for VTR) VTR LEVEL