Panasonic KX-FT934HK - Manual (Page 28)

8. Programmable Features
28
Code #39: Changing the display contrast
LCD CONTRAST
=NORMAL [ ±]
“ NORMAL” (default): For normal contrast.
“ DARKER”: Used when the display contrast is too light.
Code #41: Changing the fax activation code
FAX ACTIVATION
=ON [ ±]
If you wish to use an extension telephone (page 22) to
receive faxes, activate this feature and program the
activation code.
1. Press {MENU}.
2. Press {#}, then {4}{1}.
3. Press {A} or {B} repeatedly to select “ ON”.
4. Press {SET}.
5. Enter your code (2 to 4 digits) using the dial keys
{ 0}–{9}, {*} and {#}.
L The default code is “;;; 9”.
L Do not enter “0000”.
6. Press {SET}.
7. Press {MENU}.
Code #44: Setting the memory reception alert
RECEIVE ALERT
=ON [ ±]
To alert you with a beeping sound when a received fax
document is stored into memory due to some existing
problem.
The slow beeps will continue until you clear the printing
problem and make sure the unit is supplied with enough
paper to print the stored document.
“
ON” (default): You will be alerted to a reception problem
by a beeping sound.
“
OFF”: Deactivates this feature.
Code #46: Setting friendly reception
FRIENDLY RCV
=ON [ ±]
To receive a fax automatically when you answer a call
and hear a fax calling tone (slow beep).
“
ON” (default): You do not have to press {FAX/START}
for fax reception.
“
OFF”: You have to press {FAX/START} for fax
reception.
Code #58: Setting the scan contrast
SCAN CONTRAST
=NORMAL [ ±]
To send or copy a document with faint or dark writing, set
this feature before starting transmission or copying.
“
NORMAL” (default): Used for normal writing.
“ LIGHT”: Used for dark writing.
“ DARKER”: Used for faint writing.
L This feature is not valid if you select “ PHOTO”
resolution for sending (page 18) or copying (page 25)
a document.
Code #59: Setting the print contrast
PRINT CONTRAST
=NORMAL [ ±]
To adjust the darkness of received or copied documents.
“
NORMAL” (default): Normal contrast.
“ DARKER”: Darker contrast.
Code #73: Changing the receiving mode in the
manual answer setting
MANUAL ANSWER
=TEL [ ±]
“ TEL” (default): Telephone mode (page 21)
“ TEL/FAX”: Telephone/Fax mode (page 22)
Code #76: Setting the connecting tone
CONNECTING TONE
=ON [ ±]
If you often have trouble when sending faxes, this feature
allows you to hear connecting tones: fax tone, ring back
tone and busy tone. You can use these tones to confirm
the status of the other party’s machine.
“
ON” (default): You will hear connecting tones.
“ OFF”: Deactivates this feature.
Note:
L If the ring back tone continues, the other party’s
machine may not be a fax machine or may have run
out of paper. Check with the other party.
L The connecting tone volume cannot be adjusted.
Code #78: Changing the TEL/FAX delayed ring
setting
TEL/FAX RING
RINGS=2 [ ±]
If you use an extension telephone in TEL/FAX mode,
select the desired number of times the extension
telephone rings before the unit answers the call. You can
select “
1”, “2” (default), “3”, “4”, “5”, “6”, “7” “8” or
“ 9”. See page 22 for details.
Code #80: Resetting advanced features to their
default settings
SET DEFAULT
RESET=NO [ ±]
To reset the advanced features:
1. Press {MENU}.
2. Press {#}, then {8}{0}.
3. Press {A} or {B} repeatedly to select “ YES”.
4. Press {SET}.
5. Press {SET} again.
FT932_934HK-PFQX2561YA-en.book Page 28 Monday, May 8, 2006 5:05 PM