Panasonic AK-MSU930P - Manual (Page 7)

7
BRIGHT: Dot matrix display brightness setting
This is used to set the brightness of the
dot matrix display.
BUZZ: Buzzer setting
This is used to set the buzzer to ON or
OFF.
<CARD>: SD card read/write setting
This is used to write the camera’s data
on the SD card or read it from the card.
System switches [SYSTEM]
These are the system setting switches used to set the
down-converter mode, select the down-converter filter,
select GBR or YPbPr for the HDTV video output, select
GBR or YPbPr for the SDTV video output, select the up-
converter mode, select whether the CCU waveform
monitor control connector is to be used for SDTV or
HDTV applications, and so on.
HEAD, CCU RCV LEVEL:
Camera head, CCU unit light reception
strength level displays
These indicate the light reception
strength margins of the camera head and
CCU.
RET1, RET2, RET3, RET4: Return video settings
These are used to set the input
allocations of the return signals.
D/C MODE: Down-conversion system selection
This is used to select the down-
conversion system.
U/C MODE: Up-conversion system selection
This is used to select the up-conversion
system.
D/C LINK: Down-conversion link
This is used to decide whether to go with
the down-conversion system control
based on the AUX external input or set
the down-conversion independently.
U/C LINK: Up-conversion link
This is used to decide whether to go with
the up-conversion system control that is
linked to the down-conversion system or
set the up-conversion independently.
HD BAR: HD color bar made setting
This is used to select the HD color bar
mode.
SD BAR: SD color bar mode setting
This is used to select the SD color bar
mode.
PATHO: Pathological pattern output
This is used to forcibly output the
pathological pattern.
SET UP: Color bar setup setting
This is used to set the color bar setup.
OUTPUT SEL: Output selection
This is used to set the analog output of
the CCU to RGB or YPbPr.
MONI SEL: Monitor switch selection setting
This is used to set the monitor switch
selection to PM, WFM or the PM-WFM
link mode.
Parts and their functions
Black gamma control switch [BLK GAMMA CONTROL]
This is operable when the lamp of the BLK GAMMA ON
switch among the MODE ON/OFF switches is lighted. It
is selected to adjust the black gamma curve.
When the switch is selected, its lamp lights.
BLKR, BLKM, BLKB GAM:
Black gamma curve (R, MASTER or B)
Adjustment range: –32 (black compression) to
+31 (black expansion)
LEVEL: Black gamma level
Setting: LOW (brightness level: approx. 20%),
HI (brightness level: approx. 30%)
Matrix control switch [MATRIX CONTROL]
This is pressed to change the correction amounts for the
R-G, R-B, G-R, G-B, B-R and B-G chroma saturation.
MTX 12, SATU, PHASE
These are used to select the following 12-axis matrix
adjustment items: G, G_Cy, Cy, Cy_B, B, B_Mg, Mg,
Mg_R, R, R_Ye, Ye and Ye_G.
FUNC switches [FUNC]
ALC LEVEL:
Auto iris level
This is used to adjust the auto iris level of
the lens iris.
SPEED: Auto iris speed
This is used to set the feedback speed of
the auto iris.
WINDOW: Auto iris window
This is used to set the image detection
area window of the auto iris.
PEAK: Peak/average setting
This is used to set the ratio between the
average and peak values of the auto iris
image detection.
FAN POWER: Fan power switch
This is used to set the power of the
camera head’s fan to ON or OFF.
FAN SPEED: Fan speed
This is used to set the speed of the
camera head’s fan.
2D-M: Component 2-dimensional low-pass filter
This is used to set whether to apply the
2-dimensional low-pass filter to the
SDTV component output.
2D-E: Composite 2-dimensional low-pass filter
This is used to set whether to apply the
2-dimensional low-pass filter to the
SDTV composite output.
COMB: Comb filter mode
This is used to set the comb filter mode.
SETUP MODE: Auto setup mode setting
This is used to select the auto setup
mode setting.
REF FILE: File select
This is used to select the file attribute to
be referenced when auto setup has been
started.
MPED SET: Auto setup MPED convergence value
This is used to set the position where the
master pedestal is to be converged when
auto setup has been started.