Panasonic RX-D26 - Manual (Page 4)

RQTT0622
4
CDs
Normal play
1 2 3 4
1 Push [ CD OPEN/CLOSE] to
open the CD lid and insert the
CD.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2 Push [ CD OPEN/CLOSE] to
close the CD lid.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3 Press [CD / ] to start play.
(Unit comes on.)
Play starts from the first track and
continues to the last track.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
4 Adjust the volume.
To stop play
Press [ / CLEAR].
While stopped, the number of tracks on the CD is displayed.
Label must face upward.
Elapsed play time
Track number in play
Total playing time
Total number of tracks
Note
• If interference occurs to radios or televisions, place the unit as far as
possible from the equipment.
• Do not press [ CD OPEN/CLOSE] during play, pause or immediately
after you inserted the CD and closed the CD lid. CD may be scratched.
This unit can play CD-DA (digital audio) format audio CD-R and CD-
RW that have been finalized (a process that enables CD-R/CD-RW
players to play audio CD-R and CD-RW) upon completion of
recording.
It may not be able to play some CD-R or CD-RW due to the condition
of the recording.
“NO DISC” is displayed if there is no disc in the unit.
To pause
To search forward/
backward
To skip forward/
backward
Press [CD / ] during playback.
To resume, press [CD / ].
Hold down [ − / ] (backward) or [ / + ]
(forward) during playback or when paused.
Press [ − / ] (backward) or [ / + ] (forward)
during playback or when paused.
Program play
You can program up to 24 tracks.
Ensure CD is stopped before programming.
1 Press and hold [–PGM].
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
2 While “ ” is flashing
Press [–/ ] or [ /+] to select
the desired track.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3 Press [–PGM].
The track is programmed.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Repeat steps 2 and 3 until you have
programmed all the tracks you want.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
4 Press [CD / ].
To cancel program play mode
Press [ /CLEAR] while stopped. “CLEAR” is displayed.
The mode is also canceled if the CD tray is opened.
This will also erase the entire program.
To check program contents
“P” appears in the display when play is stopped.
Press [–/
] or [ /+] when “P” is displayed.
To check while programming press [ / CLEAR] and after “P” appears,
press [–/
] or [ /+].
Display
“— —:— —”:
Program equals, or exceeds, 100 minutes but
programming and play are still possible.
“FULL”: 24 tracks have already been programmed. The program
is full.
CD play modes
Preparations:
Press [CD / ] and then [ / CLEAR] to switch to CD mode.
You can repeat one track ( ), all tracks ( ) or play the tracks in
random order ( ).
Press [•CD PLAY MODE] to select the desired mode.
off (no indication)
These modes remain active until the indicators are cleared.
You can use repeat mode with program play.
Note
• During play, you cannot select random play.
• Random and program play cannot be performed at the same time.
Program order
Specified track number
Play time
Track number
Total play time of
programmed tracks
1 3 2 4
04.1.29, 14:16 Page 4