Panasonic RX-D26 - Manual (Page 8)

RQTT0622
8
Cassette
Has the cassette’s tab been removed? Cover the hole with adhesive tape. 5
Clean the heads. 7
The batteries are flat. Replace the batteries or connect to household AC power.
Press [ PLAY] then [ / STOP/EJECT].
Recording not possible.
Poor sound quality.
The cassette cannot be ejected or the lid can’t
be closed when loading a cassette.
Take note of the following points to extend the life of your equipment.
Always read the instructions provided with the software.
Discs
Choose discs with this mark:
Continued use of irregular shaped
CDs can damage the unit.
Do not
• use CDs with labels and stickers
that are coming off or with adhesive
exuding from under labels and
stickers.
• attach scratch-proof covers or any
other kind of accessory.
• write anything on the CD.
• clean CDs with liquids. (Wipe with a soft, dry cloth.)
• use CDs printed with label printers available on the market.
• load a blank CD-R as it will cause abnormal malfunction and may
damage the CD-R.
Cassette tapes
• Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
• Tape slack can get caught up in the mechanism and should be
taken up before the tape is played.
• Endless tapes can get caught up in the deck’s moving parts if used
incorrectly.
• Sound quality may be effected and the cassette tape may become
stuck if you do not adhere to the following.
- Do not use other stickers not included with the cassette tape.
- Place stickers on the cassette tape only as indicated.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
RQTT0622-1B
M1203YS1014
En
CD
Indicates an incorrect operation. Read the instructions.
The disc was incompletely formatted. Use the recording equipment to fully format the disc before recording.
Clean the CD.
Wait for an hour for condensation to dry, then try again.
Make sure the label is facing up.
Replace the CD if it is scratched, warped, or irregularly shaped. “ERROR” is displayed.
CD-RW cannot be read.
Play doesn’t start or display is incorrect.
Radio
Is another remote control being used? Use it further away from this unit.
Is a TV on? Move the unit away from the TV or turn it off. A lot of noise.
Audio software Specifications
Frequency range
FM 87.50–108.00 MHz (50 kHz steps)
AM 522–1629 kHz (9 kHz steps)
(Only for areas except for United Kingdom and Continental Europe)
520-1630 kHz (10 kHz steps)
Sampling frequency 44.1 kHz
Decoding 16 bit linear
Beam source Semiconductor laser (wavelength 780 nm)
Pickup
Bølgelengde
780 nm
Laserstyrke Ingen farlig stråling sendes ut
(med sikkerhets-beskyttelse)
No. of channels 2 channel, stereo
Wow and flutter Less than possible measurement data
D/A converter 1 bit DAC
Track system 4 track, 2 channel, stereo
Monitor system Variable sound monitor
Recording system AC bias
Erasing system Multi Pole magnet
Frequency range
Normal position 50–12000 Hz
Speakers
Full range 8 cm 4 Ω x 2
Jacks
Output PHONES: 3.5 mm stereo (32 Ω )
Power output (For Australia and New Zealand) 57 W (PMPO)
(For areas except for United Kingdom, Continental Europe,
Australia and New Zealand)
60 W (PMPO)
Power requirement
AC
(For United Kingdom, Continental Europe,
Australia and New Zealand)
230-240 V, 50 Hz
Power consumption: 13 W
(For others) 110-127 V/220-240 V, 50/60 Hz
Power consumption : 14 W
Battery 9 V (Six R14/LR14, C, UM-2 batteries)
• Do not use rechargeable type batteries.
Memory back-up 4.5 V (Three R6/LR6, AA, UM-3 batteries)
• Do not use rechargeable type batteries.
Dimensions (WxHxD) 408 x 163 x 273 mm
Mass
(For United Kingdom, Continental Europe,
Australia and New Zealand)
3.3 kg without batteries
(For others) 3.4 kg without batteries
Troubleshooting guide
Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not
solve the problem, consult your dealer for instructions.
Reference pages are shown as black circled numbers
2 .
Note
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Power consumption in standby mode:
(For United Kingdom, Continental Europe,
Australia and New Zealand)
1.1 W
(For others) 1.6 W
Is the AC mains lead connected to the unit? Disconnect when using batteries.
Have the batteries been inserted correctly? Check that the poles (+ and –) are correctly aligned.
2
Replace the batteries or use household AC power.
The unit doesn’t work on batteries.
“UO1” is displayed.
Common Problems
04.1.29, 14:16 Page 8