Panasonic AJ-P2C016RG - Manual (Page 161)

161 Maintenance and Inspections: Warning System
Ma
int
enan
ce
an
d Ins
pe
cti
on
s
6. Recording Error
Display window
indication
“00:00:00:11” appears in the time code
display field. Even after recording is
stopped, this display continues to blink
until the next operation is performed.
WARNING lamp
Blinks 4 times per second while recording
continues.
Tally lamp
Blinks 4 times per second while recording
continues.
Viewfinder The “REC WARNING” indicator lights up.
Warning tone
Beeps 4 times per second while recording
continues.
Warning description
This indicates a failure either in the P2
card recording or the recording circuit.
This is displayed when attempting to
record clips where the total quantity
exceeds the upper limit (1000 pieces) for
a single P2 card.
Recording/playback
operation
The recording may stop or continue.
Countermeasures
Confirm the recording/playback operation
after turning off the power supply once
and then turning it on again.
If the recording cannot be performed
normally, change the P2 card.
7. Low Wireless Signal Reception
Display window
indication
No display.
WARNING lamp
Blinks 4 times per second (during pause
and recording).
Tally lamp
Blinks 4 times per second while recording
continues.
Viewfinder
The “WIRELESS-RF” indicator lights up
while recording continues.
Warning tone
Beeps 4 times per second while recording
continues.
Warning description
This error indicates poor wireless audio
reception conditions.
Recording/playback
operation Continues to operate without receiving
the wireless microphone signal.
Countermeasures
Check the microphone power supply and
the reception status of the wireless
receiver.
8. Battery Nearly Empty
Display window
indication One of the bars in the battery remaining
indicator starts blinking.
WARNING lamp Blinks once per second.
Tally lamp Blinks once per second.
Viewfinder The “BATT” LED blinks.
Warning tone Beeps 4 times per second.
Warning description The battery is about to run out.
Recording/playback
operation
Continues to operate.
Countermeasures Replace the battery as required.
9. P2 Card Nearly Full
Display window
indication One of the bars for remaining MEDIA
capacity starts blinking.
WARNING lamp
Blinks once per second while recording
continues.
Tally lamp
Blinks once per second while recording
continues.
Viewfinder
The P2 card remaining capacity indicator
blinks.
Warning tone
Beeps once per second while recording
continues.
Warning description
The total remaining capacity of all the P2
cards is 2 minutes or less.
Recording/playback
operation
Continues to operate.
Countermeasures
Replace the cards. If there is an empty
card slot, insert a new card.
10. P2 Card Error
Display window
indication
If the error occurs during recording,
“00:00:00:11” appears in the time code
display field. The indication continues to
flash after recording is stopped and until
the next operation is performed. There is
no indication if the error occurs during
playback.
WARNING lamp
If the error occurs during recording, the
lamp flashes 4 times per second for a
period of about 3 seconds after recording
stops. The lamp does not light if the error
occurs during playback.
Tally lamp
If the error occurs during recording, the
lamp flashes 4 times per second for a
period of about 3 seconds after recording
stops. The lamp does not light if the error
occurs during playback.
Viewfinder
A flashing “CARD ERR ” appears. In
the actual indication the is replaced by
the slot number of the P2 card that
triggered the error.
Warning tone
If the error occurs during recording, the
tone sounds 4 times per second for a
period of about 3 seconds after recording
stops. The tone does not sound if the
error occurs during playback.
Warning description
An error has occurred while recording
data to or playing data from a P2 card.
Recording/playback
operation
Stop recording or playback.
Countermeasures Replace the affected P2 card.
AJ-HPX3700G-VQT1V68_eng.book 161 ページ ２００８年１０月１５日 水曜日 午後６時３８分