Panasonic AJ-P2C016RG - Manual (Page 124)

124 Preparation: Attaching the Front Audio Level Control Knob
CHARA ON button
This button is used to select whether to superimpose
characters on the video signal output to the MON OUT
connector of this unit. Note that the MON OUT
CHARACTER switch of this unit does not function when
the AJ-RC10G is connected.
Scene file
Scene files created on other types of device cannot be
read. When an attempt is made to read such a file, AJ-
RC10G displays “NG” on the liquid crystal screen.
Menu option
GAMMA menu
The options available in GAMMA-MODE-SEL are as
follows.
HD, SD, F-LIKE1, F-LIKE2, F-LIKE3, FILM-REC,
VIDEO-REC
DYMC-LVL and BSR-LVL are added to the 4th layer.
The variable ranges for these are as follows.
DYMC-LVL: 200% - 600%
BSR-LVL: 00% - 30%
Note, however, that these values can only be changed
when “FILM-REC” has been selected in GAMMA-
MODE-SEL.
V-KNSLP and V-KNPNT are added to the 5th layer.
The variable ranges for these are as follows.
V-KNSLP: 150% - 500%
V-KNPNT: 30% - 107%
Note, however, that these values can only be changed
when “VIDEO-REC” has been selected in GAMMA-
MODE-SEL.
WHITE menu
The variable range of COLR-TEMP-PRE, TEMP-A
and TEMP-B is 2300K - 9900K.
KNEE menu
CHROMA LEVEL is added to the 5th layer.
The variable range for this is OFF/–99% - +40%.
HI-COLOR LVL is added to the 6th layer.
The variable range for this is 1 - 32.
SHUTTER menu
“S.S2” can be selected in MODE.
The variable range for this is 1/1.0 - 1/250.0.
The values which can be selected in SPED differ
depending on the settings of this unit.
When “FIX” has been selected in MODE, the options
available in SPED are as follows.
1/50, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000,
1/2000, HALF, 180.0d, 172.8d, 144.0d, 120.0d,
90.0d, 45.0d
The values that can be selected in SPED differ
depending on the settings of the SYSTEM MODE
menu option in this unit.
SYNCRO SCAN DISP is added to the 2nd layer.
When “S.S” has been selected in MODE, it is possible
to select between SEC and DEG as units for the
values displayed in SPED. The changes to the units
are reflected in this unit.
When “S.S” has been selected in MODE, the variable
ranges of SPED are as follows.
For SEC: 1/1.0 - 1/7200 (selectable values differ
depending on the settings of this unit)
For DEG: 3.0d - 350.0d
SKIN DTL menu
The options available in OUTPUT are as follows.
MONI, SDI A, SDI B
A zebra is added to the colors of the table selected in
SDTL.
SCORG of the 3rd layer changes to SKIN DTL
EFFECT. The variable range for this is 0 - 31.
FUNC menu
The options available in SELECT of the 4th layer are
as follows.
INH, I.OVR, S.BLK, B.GAMMA, Y GET, DRS,
ASSIST, C.TEMP, FRATE, VFR, VF GAM, AUDIO
CH1, AUDIO CH2, REC SW, RET SW, PRE REC,
SLOT SEL, PC MODE
Note, however, that the C.TEMP function will not work
when assigned to a user button on AJ-RC10G.
The variable range of BLK-GAMMA of the 5th layer is
–8 - 8.
RANGE is added next to BLK-GAMMA of the 5th
layer. The variable range for this is 1 - 3.
FRAME-RATE is added to the 6th layer.
The variable range for this is 1 - 60. Note, however,
that the variable range will differ depending on the
settings of this unit. Also, if the unit is not recording
VFR, values can be changed but there is no effect on
the image.
If you use the FRONT AUDIO LEVEL control frequently,
attach the accessory knob so that it can be easily operated.
a. FRONT AUDIO LEVEL control
b. Screw
c. Marks
d. Knob (included)
e. Screw (included)
Remove the screw in the center of the FRONT AUDIO
LEVEL control, and attach the accessory knob (included)
using the screw (included). When attaching the knob, be
sure to align the marks on the control with the marks on the
knob.
Attaching the Front Audio Level Control Knob
a
b
d c
e
AJ-HPX3700G-VQT1V68_eng.book 124 ページ ２００８年１０月１５日 水曜日 午後６時３８分