Pioneer PRO-1000HDI - Manual (Page 23)

19
PRO-1000HD I / PRO-800HD I
Setting Up the System
Setting Up the System
CLAMP POSITION setup
Depending on the signal, analog RGB signals may result
in the screen image appearing with a whitish or greenish
cast. In such cases, set “CLAMP POSITION” to LOCKED.
÷ Normally, leave this setting at AUTO.
Setup of CLAMP POSITION
1 Press MENU to display the menu screen.
The menu screen appears.
MAIN MENU INPUT1
SELECT ENTER EXIT SET MENU
PICTURE SCREEN SET UP OPTION
: 0
: 6 +
+
+ 0
: 6 0
: 6 0
: 0
: 0
C O N T R A S T : 0
B R
R L E V E L I GH T .
.
G L E V E L .
B L E V E L .
H E NH AN CE .
V E NH AN CE .
R S E T E
2 Press 2/3 to select SET UP.
PICTURE SCREEN SET UP OPTION
: V G A
: NT
: A U T O
S E T T I N
C L AMP
POWE R
:
G
OF F
P S I T I O N O
M N A GEME A
I N P UT I N P UT 1 L E B L A
MAIN MENU INPUT1
3 Press 5/∞ to select CLAMP POSITION.
PICTURE SCREEN SET UP OPTION
: NT
S E T T I N
C L A MP
POWE R
:
G
OF F
P S I T I O N O
M N A GEME A
I N P UT I N P UT 1 L E B L A
: V G A
: A U T O
MAIN MENU INPUT1
4 Press SET to select LOCKED.
PICTURE SCREEN SET UP OPTION
: NT
S E T T I N
C L A MP
POWE R
:
G
OF F
P S I T I O N O
M N A GEME A
I N P UT I N P UT 1 L E B L A
: V G A
: L O CK E D
MAIN MENU INPUT1
Mode selection will change as follows each time SET
is pressed.
5 When the setup is completed, press MENU to exit
the menu screen.
Notes
÷ Make this CLAMP POSITION setting for each applicable input
(INPUT1 and INPUT2).
÷ When using this setup, be sure to carefully check the signal
output of the component that you are using. For details, please
refer to the instruction manual supplied with the component
you are connecting.
9 Press SET repeatedly to select the input signal
format.
Selection will change as follows each time SET is
pressed.
RGB
COMPONENT
The table below shows what settings are appropriate
and available for the type of connections made.
Set SETTING and VIDEO SIGNAL as follows.
10 When the setup is completed, press MENU to exit
the menu screen.
Note
Make this setup for each input (INPUT1 and INPUT2).
Component video output
of a DVD player, etc.
RGB video output of a
video deck etc., with RGB
output
RGB video output of a PC
Connected
component
VIDEO SIGNAL SETTING
SET UP
VIDEO
VIDEO
VGA
WVGA
XGA
WXGA
COMPONENT
RGB
Not supported
3 AUTO
LOCKED 2
8
When inputting a video signal (When VIDEO is
selected), press
5/∞ to select VIDEO SIGNAL.
SELECT CHANGE EXIT SET MENU
: I N P UT L E B L A
: V I D E O
V I D E O : R G B
: A U T O
S E T T I N
S I GNA L
C L AM
OF F A UT O
P
P O WER
G
: OF F
P S I T I O N O
D I G I T A L NR
: O F F
H I GH C O T N R A T S : O F F
: L OW
C OL OR T M E P : M I D DL E
MAIN MENU INPUT1
I N P UT 1
P URE I C N MA E
PICTURE SCREEN SET UP OPTION