Pioneer PRO-1000HDI - Manual (Page 30)

26
PRO-1000HD I / PRO-800HD I
3 OFF
ON 2
Automatic Power OFF
This display is equipped with automatic power-
management and auto-power-off functions, which allow
the unit to automatically switch to power-saving mode
when no sync signal is detected.
(A warning message appears onscreen before these
functions operate.)
Notes
÷ Power Management settings are supported only when a
computer signal is input to INPUT 1.
÷ The auto-power-off function can be used only in those cases
other than the inputs used in the preceding item.
÷ Always turn off the plasma display’s main power switch when
not using the display for extended periods of time.
1 Press MENU to display the menu screen.
MAIN MENU INPUT1
SELECT ENTER EXIT SET MENU
PICTURE SCREEN SET UP OPTION
: 0
: 6 +
+
+ 0
: 6 0
: 6 0
: 0
: 0
C O N T R A S T : 0
B R
R L E V E L I GH T .
.
G L E V E L .
B L E V E L .
H E NH AN CE .
V E NH AN CE .
R S E T E
2
Press 2/3 to select SET UP.
[When computer signal is input to INPUT 1]
SELECT ENTER EXIT SET MENU
PICTURE SCREEN SET UP OPTION
: V G A
: NT
: A U T O
S E T T I N
C L AMP
POWE R
:
G
OF F
P S I T I O N O
M N A GEME A
I N P UT I N P UT 1 L E B L A
MAIN MENU INPUT1
[In all other cases]
SELECT ENTER EXIT SET MENU
PICTURE SCREEN SET UP OPTION
: V G A
:
: A U T O
S E T T I N
C L AMP
A U T O P OWE R
:
G
O F F O F F
P S I T I O N O
I N P UT I N P UT 2 L E B L A
MAIN MENU INPUT2
3 Press 5/∞ to select either the POWER
MANAGEMENT or AUTO POWER OFF mode.
[When computer signal is input to INPUT 1]
SELECT CHANGE EXIT SET MENU
PICTURE SCREEN SET UP OPTION
: A U T O
S E T T I N
C L AMP
POWE R
:
G
OF F
P S I T I O N O
M N A GEME A
I N P UT I N P UT 1 L E B L A
: V G A
: NT
MAIN MENU INPUT1
[In all other cases]
PICTURE SCREEN SET UP OPTION
: V G A
: A U T O
S E T T I N
C L AMP
A U T O P OWE R
:
G
O F F O F F
P S I T I O N O
I N P UT I N P UT 2 L E B L A
:
MAIN MENU INPUT2
4 Press SET to confirm selection of the POWER
MANAGEMENT or AUTO POWER OFF.
÷ When OFF is selected, the display will continue in
operating mode, regardless of the presence/
absence of an input sync signal.
÷ When POWER MANAGEMENT: ON is selected, if
a sync signal is not detected, a warning message is
displayed for 8 seconds, after which the display
automatically enters the power-saving mode (*1)
and the STANDBY/ON indicator flashes green. If a
sync signal (*2) is input again later, the plasma
display automatically returns to normal operating
mode.
*1. Power consumption about 1W
*2. Except when input signal is G on SYNC or composite
SYNC
÷ When AUTO POWER OFF: ON is selected, if no
sync signal is detected for 8 minutes or more, a
warning message will be displayed for 30 seconds,
after which the unit's power will switch to
STANDBY mode.
5 When the setup is finished, press MENU to exit
the menu screen.
Note
The POWER MANAGEMENT and AUTO POWER OFF functions
must be set individually for each input (INPUT 1 – 5).
To return to operating mode:
÷ To return to normal operation from POWER
MANAGEMENT mode: either operate the computer,
or press INPUT on the main unit operating panel or
remote control unit.
÷ To return to normal operation from AUTO POWER
OFF mode: Press STANDBY/ON on the main unit
operating panel or remote control unit.
Operations