Panasonic SC BTT268 - Manual (Page 17)

Getting s
tar
te
d
17
VQT3M40
The configuration of your network is about to begin. If you
failed to make the settings, refer to “When you experience
problems with settings”.
Network Easy Setting (Home Network Connection Check)
Network Easy Setting (Internet Connection Check)
≥ Refer to the operating instructions of the hub or router.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in
the Setup menu. ( 34)
≥ You can redo these settings individually using “Network Settings”. ( 34)
≥ Please be aware that connecting to a network without encryption may
result in the content of the communication being illegitimately viewed by a
third party, or the leaking of data such as personal or secret information.
If you have more than one Panasonic player/recorder and the
remote control operates both products at once, you will
need to change the remote control code on one product to
prevent this occurrence. (
34, “Remote Control Code”)
Occasionally, Panasonic may release updated firmware for this
unit that may add or improve the way a feature operates.
These updates are available free of charge.
This unit is capable of checking the firmware automatically
when connected to the Internet via a broadband connection.
When a new firmware version is available, the following
message is displayed.
To update the firmware
Press [HOME] select “Others” [OK] [OK] (“Setup”)
select “Others” [OK] select “Firmware Update”
[OK] select “Update Now” [OK]
DO NOT DISCONNECT the unit from the AC power or perform
any operation while the update takes place.
After the firmware is installed, “FINISH” will be displayed on the
unit’s display. Unit will restart and the following screen will be
displayed.
≥ If downloading on this unit fails or this unit is not connected to the
Internet, then you can download the latest firmware from the
following website and burn it to a CD-R to update the firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
To show the firmware version on this unit. (
34, “System Information”)
≥ Downloading will require several minutes. It may take longer or may
not work properly depending on the connection environment.
≥ If you do not want to check for the latest firmware version, set “Automatic
Update Check” to “Off”. ( 34)
Network Easy Setting
When you experience problems
with settings
Display
Check the
following
1. LAN cable connection :Fail ≥ Connection of
the LAN
cables (
15)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection :Pass ≥ Connection
and settings of
the hub and
router
≥ Settings of “IP
Address /
DNS Settings”
(
34)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection :Pass
2. IP address setting :Pass
3. Connection to gateway :Fail
Display Check the following
Cannot find the server.
(Error code: B019) ≥ “Primary DNS” and “Secondary
DNS” Settings of “IP Address /
DNS Settings” (
34)
Failed to connect to the
server.
(Error code: B020) ≥ The server may be busy or the
service may have been
suspended. Please wait a few
moments, and then try again.
≥ Settings of “Proxy Server
Settings” ( 34) and the router.
OK
Network Easy Setting (Home Network Connection Check)
Yes No
Complete.
1. LAN cable connection
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
: Fail
: Fail
: Fail
OK
Network Easy Setting (Internet Connection Check)
Complete.
- Connection to the Internet : Fail(Error code: B019)
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the owner's manual for the cause of
the error and the solution for it.
Press [OK].
Reprogramming the remote
control
Firmware updates
New firmware is available.
Please update firmware in Setup.
The firmware was updated.
Current Version : x.xx
RETURN
OK
SC-BTT268_P_eng.book 17 ページ ２０１０年１２月１７日 金曜日 午前８時５分