Pioneer DVR-433H-K - Manual (Page 40)

Recording 05
40
En
4 Use the AUDIO (SHIFT + 1) button to select the
audio channel to record.
See Changing audio channels on page 29 for more on
this.
• When recording in VR mode, if a broadcast is
bilingual, both audio channels are recorded, allowing
you to switch the audio channel on playback. The
only exception to this is when the picture quality is set
to
LPCM , in which case you do need to select the
audio channel before recording.
5 Press ì REC to start recording.
If you want to set a recording end time, press the ì REC
button repeatedly. The recording time increases in 30
minute increments, up to a maximum of six hours. The
time the recording will end is shown on-screen and in the
front panel display. When the recording ends, the
recorder automatically switches into standby if no other
operation is being performed.
• To cancel the set recording time, press ì REC .
• If you want to pause recording at any time, press
. Press again to restart the recording. (If recording
to the HDD or in VR mode, a new chapter is started
after recording restarts)
6 To stop the recording, press STOP REC.
• If you set the recording time in the previous step, you
can still stop the recording anytime by pressing
STOP REC .
• Recording will stop automatically when there is no
more space on the HDD/DVD, or after 12 hours of
HDD recording (whichever is sooner).
Tip
• During recording you can turn on/off the SCART loop
through function. During recording, press the front
panel
button to switch to SCART THRU (loop
through on), or to switch to SCART NORM (loop
though off). Note that you can’t switch loop through
on if recording from the
AV2/AUTO START
REC(INPUT 1/DECODER) or AV1(RGB)-TV
connectors. Also, loop through is automatically reset
to off after recording has finished.
Direct recording from TV
If you connected this recorder to your TV using a SCART
cable, and your TV supports Direct Recording, you can
record whatever is currently being shown on the TV
without having to worry about what channel preset the
recorder is on. Check the instructions that came with
your TV if you’re not sure whether your TV supports this
feature.
1 If necessary, load a recordable disc.
2 Set the picture quality/recording time using the
REC MODE (SHIFT + ) button.
3 Press TV DIRECT REC (SHIFT + ì REC) to start
recording.
If you want to set a recording time, press the ì REC
button repeatedly. The recording time increases in 30
minute increments, up to a maximum of six hours. You
can see the recording time on-screen and in the front
panel display. When the recording ends, the recorder
automatically switches into standby if no other operation
is being performed.
• To cancel the set recording time, press ì REC .
• If you want to pause recording at any time, press
. Press again to restart the recording. (If recording
to the HDD or in VR mode, a new chapter is started
after recording restarts)
4 To stop the recording, press STOP REC.
• If you set the recording time in step 3 , you can still
stop the recording anytime by pressing STOP REC .
• Recording will stop automatically when there is no
more space on the HDD/DVD, or after 12 hours of
HDD recording (whichever is sooner).
Tip
• You can press TV DIRECT REC ( SHIFT + ì REC )
while the recorder is in standby to switch on and
immediately start recording.
• Please note that you can’t record from another
component (VCR, etc.) that is connected by a SCART
cable to the
AV2/AUTO START REC(INPUT 1/
DECODER) connector using the TV Direct Recording
feature.
DVD RECORDER
SKIP
TV DRECT REC
REC MODE
ST0P REC REC SHIFT
ONE TOUCH
COPY
BACK CM
ì
DVR-433H_UK.book 40 ページ ２００５年３月１日 火曜日 午後５時６分