Speaker distance bass peak level x-curve, The system setup menu 08, Speaker distance – Pioneer VSX-2016AV User Manual
Page 47: Bass peak level, X-curve
The System Setup menu
08
47
En
Tip
• You can change the channel levels at any time by
pressing
CH LEVEL
then using
/
on the remote
control.
Speaker Distance
For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
1
Select ‘Speaker Distance’ from the Manual SP Setup
menu.
2
Adjust the distance of each speaker using the
/
buttons.
You can adjust the distance of each speaker in 0.1 meter
increments.
3
When you’re finished, press
RETURN
.
You will return to the Manual SP Setup menu.
Tip
• For best surround sound, make sure the surround
back speakers are the same distance from the
listening position.
Bass Peak Level
Some audio sources (for example, Dolby Digital and DTS)
include ultra-low bass tones. Set the bass limiter as
needed to prevent the bass from distorting the sound.
1
Select ‘Bass Peak Level’ from the Manual SP Setup
menu.
The current setting is displayed. When
OFF
is displayed
the attenuator is off (bass output is not affected).
2
Select a setup option.
•
Setting Start
– The volume is set to –60 dB, a test
tone plays back and you make the setting.
•
Setting Clear
– Clears any previous setting and
switches limiting off.
3
If you selected ‘
Setting Start’
, use
/
to adjust
the test tones and specify the bass peak level then press
ENTER
.
Set the bass peak level gradually, then press
ENTER
at
the point just before the tone starts to distort.
1
The
display on the receiver shows
RESUME
while the volume
returns to its original position, then you automatically
return to the main Bass Peak Level menu.
4
When you're finished, press
RETURN
.
You will return to the Manual SP Setup menu.
X-Curve
Most soundtracks mixed for cinema sound too bright
when played back in large rooms. The X-Curve setting
acts as a kind of re-equalization for home theater
listening, and restores proper tonal balance of movie
soundtracks.
2
1
Select ‘X-Curve’ from the Manual SP Setup menu.
5.Manual SP Setup
:Return
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
5c.Speaker Distance
L
3.0 m
C
[ 3.0 m ]
R
[ 3.0 m ]
SR
[ 3.0 m ]
SBR
[ 3.0 m ]
SBL
[ 3.0 m ]
SL
[ 3.0 m ]
SW
[ 3.0 m ]
:Finish
5.Manual SP Setup
:Return
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
5d.Bass Peak Level
:Return
Bass Peak Level
:OFF
[Setting Start
]
[Setting Clear
]
Note
1 If the
YES
or
PLUS
setting on the subwoofer is selected (in
Speaker Setting
on page 45), the test tone will only play back from the subwoofer. If not, the
test tone will play back from the front and surround speakers set to
LARGE
.
2 Since the principal is the same, X-Curve isn’t applied when you’re using any of the Home THX modes (see
Using the Home THX modes
on page 27).
5d.Bass Peak Level
:Return
Bass Peak Level
:OFF
[
Setting Start
]
[Setting Clear
]
Enter:Setting Start
5d.Bass Peak Level
Bass Peak Level
-60dB
Increase the Bass
Peak Level to
a comfortable volume
(-80dB = no sound)
ENTER:Finish :Cancel
5.Manual SP Setup
:Return
a.Speaker Setting
b.Channel Level
c.Speaker Distance
d.Bass Peak Level
e.X-Curve
f.THX Audio Setting
5e.X-Curve
63
125
250
500
1k
2k
4k
8k
16k
X-Curve
-2.0dB/oct
:Finish
VSX-2016_HY.book.fm 47 ページ ２００６年２月２４日 金曜日 午後１２時４０分