Philco Crafts PVD1000 - Manual (Page 17)

-17- EN
Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit consulting the
following checklist.
NOTES:
• Some functions are not available in specifi c modes, but this is not a malfunction. Read the description in this Owner’s Manual
for more details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
• When playing Video CDs with PBC function, some operations (e.g., select and track repeat) cannot be performed.
Information
Hint
• If you do not wish
to initialize at step
3, select “NO”.
2
Select “INITIALIZE”.
4
To exit the
menu
3
Select “YES”.
1
Press [SETUP].
SETUP
QUICK
CUSTOM
INITIALIZE
SETUP INITIALIZE
Initialize?
NO
YES
SETUP
Press twice.
SETUP
SETUP
QUICK
CUSTOM
INITIALIZE
STOP
ENTER ENTER ENTER ENTER ENTER ENTER
Problem Solution
No power –Check if the AC power cord is properly connected.
–Unplug the outlet once, and wait for 5-10 seconds and then plug it in again.
No sound or picture –Check if the TV is switched on.
–Check the video connection.
–Check the VIDEO/AUDIO cable connections to the TV.
(See page 6.)
Distorted picture –Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
–Connect the unit directly to the TV.
Completely distorted picture or
black/white picture with DVD –Connect the unit directly to the TV.
–Make sure the disc is compatible with the unit.
No sound or distorted sound –Adjust the volume.
–Check that the speakers are connected correctly.
No audio at digital output –Check the digital connections.
–Check if the audio format of the selected audio language matches your receiver capabilities.
No DTS audio is output. –This unit does not support DTS audio.
–This is not a malfunction.
Picture freezes momentarily during
playback. –Check the disc for finger prints/scratches and clean with a soft cloth wiping from center to edge.
Disc can’t be played. –Clean the disc.
–Ensure the disc label is facing up.
–Check if the disc is defective by trying another disc.
–Cancel the parental lock or change the control level.
–Insert a correct disc that plays on this unit.
–Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface.
No return to start-up screen when
disc is removed. –Reset the unit by switching the unit off, then on again.
The unit does not respond to the
remote control. –Aim the remote control directly at the sensor on the front of the unit.
–Reduce the distance to the unit.
–Replace the batteries in the remote control.
–Re-insert the batteries with their polarities (+/– signs) as indicated.
–Tune your radio to an empty AM station so that you hear a lot of static. Then, turn the volume up. If you
hear some signal sound from the radio by pressing buttons on the remote control, the remote control is
working.
Buttons do not work or the unit
stops responding. –To completely reset the unit, unplug the AC cord from the AC outlet for 5-10 seconds.
The unit does not respond to some
operating commands during play-
back. –Operations may not be permitted by the disc. Refer to the instructions of the disc.
The unit cannot read CDs / DVDs. –Use a commonly available cleaning CD / DVD to clean the lens before sending the unit for repair.
Angle does not switch. –The angle cannot be switched for DVDs which do not contain multiple angles. In some cases multiple
angles are only recorded for specific scenes.
The password for rating level has
been forgotten. –Enter the default password “4737”, then your forgotten password will be cleared.
Information
Reset to the Default Setting (except for PARENTAL Setting)
SETUP menu
ENTER ENTER
E6C61UD.indd 17 E6C61UD.indd 17 2006/08/18 13:00:44 2006/08/18 13:00:44