Panasonic PT-DZ12000E - Manual (Page 121)

ENGLISH – 121
Information
Model No. PT-D12000E PT-DZ12000E
Interface
ports
RGB2 input
terminal
1 set of high-density, D-sub 15p (female)
[For YP
B
P
R
input]
Y: 1.0 V [p-p] synchronization signal included, P
B
P
R
: 0.7 V [p-p] 75 Ω
[For RGB input]
0.7 V [p-p] 75 Ω For G-SYNC: 1.0 V [p-p] 75 Ω
HD/SYNC: TTL, high-impedance, positive/negative polarity automatically
adjusted
VD: TTL, high-impedance, positive/negative polarity automatically adjusted
HD/SYNC, and VD terminals are not compliant with 3-value direct SYNC. •
Video input/output
terminal 1 set BNC
1.0 V [p-p] 75 Ω (Active through for Video output)
S-video input
terminal 1 set Mini DIN 4p
Y 1.0 V [p-p] C 0.286 V [p-p] 75 Ω Compliant with S1 signals
DVI-D input
terminal
1 set
DVI 1.0 compliant
HDCP (Single link only) compatible
LAN terminal
1 set (Used for network connection)
10BASE-T/100BASE-TX
PJLink™ compatible
Serial input
terminal 2 sets D-sub 9-pin (female), RS-232C/RS-422 compliant
Used for personal computer control
Serial output
terminal 1 set D-sub 9-pin (male), RS-422 compliant
Used for personal computer control
Remote1 input/
output terminal 1 set each for M3 pin jack
Wired remote control, used for link control
Remote2 terminal
D-sub 9p (female)
Used for external control
Length of power supply cord 3.0 m
Cabinet Molded resin
Outside dimensions Width: 578 mm, Height : 320 mm, Depth: 643 mm
Weight approx. 35 k g (without optional projection lens) *3
Working environment condition
Ambient temperature *4 : 0 C to 45 C
Ambient humidity: 10 % to 80 % (no condensation)
Remote
control
Power source 3 V DC (two AA dry cells)
Operation range approx. 30 m (in front of beam receiver)
Mass 134 g (including dry cells)
Outside dimensions Width: 51 mm, Thickness: 23 mm, Depth: 176 mm
Optional
Hanging attachment (For high ceiling): ET-PKD100H
Hanging attachment (For low ceiling): ET-PKD100S
Projection lens:
ET-D75LE1, ET-D75LE2, ET-D75LE3, ET-D75LE4,
ET-D75LE5, ET-D75LE6, ET-D75LE8
DVI-D input module: ET-MD77DV
SD-SDI input module: ET-MD77SD1
HD/SD-SDI input module: ET-MD77SD3
Dual link HD/SD-SDI input module: ET-MD100SD4
Replacement Lamp Unit: ET-LAD12K (single bulb),
ET-LAD12KF (4 bulbs)
*1 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*2 70˝ – 300˝ for ET-D75LE5
*3 This is the average value. It may differ depending on each product.
*4 When the projector is used in high altitude mode (1 400 to 2 700 m), the ambient temperature is 0
C to 40 C .
Furthermore, if the ambient temperature becomes 40 C or more (35 C in high altitude mode) when using the
projector with lamp 4 lit, light output may be reduced by approximately 30% to protect the projector.
When a smoke cut filter is used, the ambient temperature is 0
C to 35 C . However, use at high altitudes is not
possible.