Panasonic WJ-PB65E01 - Manual (Page 4)

4
Firmware Update
This chapter explains about how to update the firmware
version of WJ-SX650 Series. To update the firmware ver-
sion, installation of the Firmware update tool on the PC is
required.
■ System Requirements of a PC
The PC should meet the following requirements.
OS:
Microsoft ® Windows ® 2000 Professional SP4
Microsoft ® Windows ® XP Professional SP2
Microsoft ® Windows ® XP Home Edition SP2
Note: To work the Firmware update software on the PC,
Microsoft ® .NET Framework 1.1 needs to be installed.
If you try to install the Firmware update software on a
PC without Microsoft
® .NET Framework 1.1, it will be
installed along with the software.
OS language:
English
PC:
IBM PC/AT Compatible
CPU:
Intel ® Pentium ® 3, 500 MHz or faster
Memory:
128 MB or more
Hard drive space:
30 MB or more for installation of the Firmware update soft-
ware
50 MB or more for installation of WJ-SX650 Series Initial
Setup Tool
Note: If Microsoft ® .NET Framework 1.1 has not been
installed on the PC, 160 MB or more is required.
Monitor:
1 024 x 768 pixels or more, HIGH color 16 bit or more
Serial Interface:
9-pin D-sub connector
■ Installation and Uninstallation
● Installation
1. Insert the supplied CD-ROM into the CD-ROM drive on
the PC.
2. Double-click "setup.exe" in the "PWriter" folder of CD-
ROM.
The installation wizard will be displayed on the PC
screen.
3. Follow the instruction message on the PC screen to
complete the installation.
Note: In the factory default installation, C:\Program
Files\Panasonic\Firmware is created, and files will be
copied to the directory.
● Uninstallation
1. Select "Control Panel" - "Add/Remove Programs".
Add/Remove Programs window will be displayed on the
PC screen.
2. Select "Firmware version up software". Click "Remove"
or "Change/Remove", and follow the directions.
Note: If the Firmware update software has already been
installed on a PC, installation is impossible.
Install the application again after uninstallation.
■ PC Connection
An RS-232C crossing cable (9-pin D-sub) is used for con-
nection between WJ-SX650 Series and PC.
<SERIAL port> (Output rear board)
VIDEO OUT 3 VIDEO OUT 4 VIDEO OUT 2
MODE MODE MODE MODE
3 C
IN X-2
IN X-1
VIDEO OUT 1 ALARM IN
1 16
32
15
31 30
14 13
29 28
12 11
27 26
10 9
25
CAMERA IN
24
8 7
23 22
6 5
21
2
B
1
2
3
20
4 3
19 18
2 1
17
DATA DATA EXTENSION 1 TERM.
OFF ON
OUT IN OUT X-3
OUT X-2
1 2 3 4 AC IN 3
2
1
A
1 2 3 4 5 6 7 8 MONITOR OUT 9 10 11 12 13 14 15 16
ALARM OUT 2 ALARM OUT 1
SERIAL VS OUT
VS IN
VS OUT
(THRU)
EXTENSION 3 IN EXTENSION 2 IN
4
MODE RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
2 1
IN C-3
4
MODE RS485 (CAMERA) RS485 (CAMERA)
3
MODE MODE MODE
2 1
IN B-3
TERM.OFF ON
MODE
TERM.ON
MODE
SIGNAL GND
DATA 4 HDR4/TMNL8 HDR2/TMNL4
DATA 3 HDR3/TMNL7 HDR1/TMNL3
DATA 2 TMNL6 TMNL2
DATA 1 TMNL5 TMNL1/PS DATA Video Output Board 2 Video Output Board 1
SIGNAL GND Video Output Board 1 Only
ON 4-Line
RS485(CAMERA) SET UP
MODE ON 4-Line MODE
NETWORK OUT X-1
10/100 BASE-T
9-pin D-sub
(Female)
9-pin D-sub
(Female)
Rear Side of WJ-SX650 Series
(WJ-PB65E01 installed)
PC
Cross cable