Panasonic SC-HT830V - Manual (Page 11)

11
RQT7921
\
∫ Batteries
Do not:
≥mix old and new batteries.
≥use different types at the same time.
≥heat or expose to flame.
≥take apart or short circuit.
≥attempt to recharge alkaline or manganese batteries.
≥use batteries if the covering has been peeled off.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
Remove if the remote control is not going to be used for a long period
of time. Store in a cool, dark place.
∫ Use
Aim at the sensor ( l 14), avoiding obstacles at a maximum range of 7
m (23 feet) directly in front of the unit.
After plugging the unit into your household AC outlet and pressing [ Í]
to turn the unit on for the first time, the unit automatically tunes in all
the channels it can receive and sets the clock.
The unit determines the type of transmission, TV or CATV, as follows:
TV: when there are less than 5 CATV channels.
CATV: when there are 5 or more CATV channels.
Preparation
≥Confirm that the antenna is connected correctly.
≥Turn on the television and select the video input for the VHS.
≥Press [VHS] to put the remote control in VHS mode.
Press [ Í] to turn on the unit.
Plug-in Auto Tuning starts and the unit puts the stations it can receive
into channels (
l 37, Channel range).
The unit starts auto clock setting when finished, then displays the time.
[Note]
If auto tuning stops partway (by changing the source, turning the unit
off, or due to a power failure).
1 Disconnect the AC power supply cord on the main unit and then
reconnect it.
2 Turn on the main unit.
To cancel partway
Press [MENU].
∫ To start Plug-in Auto Tuning again (after relocation, for
example)
Preparation
≥Press [Í] to turn on the unit.
≥Make sure there is no video cassette tape loaded in the unit.
≥Press [DVD/VHS] to select “VHS” as the source.
1 Press and hold [
W CH] and [X CH] on the main unit simultaneously
for 3 seconds until the channel changes to “2”.
2 Disconnect the AC power supply cord on the main unit and then
reconnect it.
3 Turn on the main unit. Plug-in Auto Tuning restarts.
∫ To set the channels manually ( l 37 ).
∫ If the unit couldn’t set the clock automatically
The MANUAL CLOCK SET screen appears. Set the time manually
(
l 36).
VOLUME
1 2 3
4 5 6
7 8
0 DISC
9
CH
NAVI
SKIP SLOW/SEARCH
MENU
ENTER
DIRECT
NAVIGATOR
TOP MENU
RETURN
STATUS/
FUNCTIONS
TV
FM/AM DVD/VHS
DVD TV VHS TUNER
PICTURE MODE
SETUP
OPEN/CLOSE/EJECT JET REW
ENTER
PLAY
LIST
INPUT SELECTOR
DVD/VHS
VHS
MENU
S10
CH POWER
/ I
OPEN/CLOSE EJECT
DISC CHECK
/REW FF/
STOP PLAY
DOWN UP PHONES
VOLUME
STOP
-DEMO
PLAY
H.BASS REC
CH
STEP
6
The remote control
Remote control Batteries
1
2
3
R6/LR6, AA, UM-3
≥Insert so the poles (i and
j) match those in the
remote control.
≥Do not use rechargeable
type batteries.
Antenna system and channel captions all revert to the default
values when you perform the procedure above. Reset the timer
recording settings. (If necessary reset the clock first.
l 36,
CLOCK SET)
STEP
7
Plug-in Auto Tuning
AUTO CHANNEL SET
PROCEEDING
END :MENU
2
Disappears 2
RQT7921-P_ENG.book 11 ページ ２００５年２月４日 金曜日 午後４時５８分