Napco Security Technologies WI1501A - Manual (Page 22)

Freedom F-64 Installation Instructions L
NAPCO Security Systems
WI1501A 9/06

Page 22
Day Zone (Open; Short); Alarm on Day Zone; Disable Auto-Reset on Day Zone; Reset Day Zone with Arm/Disarm Only; Day
Zone Trouble on Open
A Day Zone will give an audible and visual indication at the keypad/Touchpad if there is a problem on the loop while disarmed. Open-
and short-circuit conditions are programmed separately, by zone. This feature may be used to warn of a problem (a break in a window
foil, for example) during the day, when the panel is not normally armed. When the Day Zone is tripped, "DAY ZONE TRBL" and the
zone number(s) will alternately display at the keypad/Touchpad and the sounder will pulse. Press RESET to silence the sounder and
reset the keypad/Touchpad . "ZONE FAULT" will be displayed until the condition is corrected. If Reset Day Zone With Arm/Disarm
Only is programmed, reset the Day-Zone indication at the keypad/Touchpad. A User Code is required to reset the keypad display (for
Touchpads, insert the Master I-FOB into the face of the Touchpad). If Alarm on Day Zone is programmed for a zone, a Day Zone con-
dition will cause the alarm outputs programmed for that zone (sirens, relays) to activate. If Day Zone Trouble on Open is programmed,
a zone configured as a 24 hour zone reports an alarm on short and a Day Zone trouble on an open loop.
Note: (1) If a zone is programmed for both "Day Zone Open" and "Day Zone Short", either condition must be reset before the other can
activate. (2) Day Zone Short will not function if No EOL Resistor is also programmed. Report Trouble or Trouble Restore is pro-
grammed in conjunction with Day Zone Open/Day Zone Short and Trouble on Open/Trouble on Short (the trouble reported will be that
programmed under Day Zone Open and/or Day Zone Short).
Note: Do not program a Day Zone for 24-hour protection. The keypad/Touchpad will annunciate as a Day Zone but the panel will trans-
mit an Alarm Code and a Trouble Code when tripped.
Dealer Security Code
Using the F-64PROG programmer, the factory-programmed Dealer Security Code is "456789". Use this code to enter the Easy Menu
Driven Program Mode to program (or change) the Dealer Security Code. The Dealer Security Code is needed to enter the Easy Menu
Driven Program Mode, thus allowing the dealer to program codes, zone features, reporting features and zone descriptions. This code
should be changed as required.
Dealer Program Mode; Easy Menu-Driven Program Mode; Direct Address Program Mode
See WI1502 for complete information. For use by dealers and installers only via an F-64PROG programmer. Comprises two opera-
tional states:
• EASY MENU DRIVEN PROGRAM MODE - Used with new "out of the box" panels (or "Cold Started" panels), this mode allows the
dealer to customize the factory panel program to best suit the installation. The Easy Menu-Driven Program Mode is a menu-
driven utility that prompts the installer to configure the system. Press RESET at any time to exit, thus entering Direct Address Pro-
gram Mode, defined below.
• DIRECT ADDRESS PROGRAM MODE - Additional programming changes, if necessary, can be made in the Direct Address Pro-
gram Mode. In this mode, the programming address is accessed directly and re-configured by the installer.
Dial-Tone Detection; Disable Auto Dial-Tone Detection
The panel features automatic dial-tone detection to ensure that a dial tone is present before the communicator dials. To disable this
feature, program an "8" in Location 0394.
When an "E" is programmed before the first digit of an outside telephone number, the communicator dial-tone detection circuit is set to
detect the standard 440Hz dial tone. The "E" is generally entered in the location immediately preceding the telephone number. It may
be necessary to program at least one 4-second pre-dial delay before a dial-tone detection "E". With certain nonstandard exchanges,
pre-dial delay "D"s may be used without a dial-tone detection "E". (See Access Number for Outside Line; Pre-Dial Delay; Telephone
Numbers)
Digital Dialer Report Enter/Exit Test Mode
Initiation Report. At the initiation of a test, the control panel sends a message to the central station that a test is in progress. The "Fault
Find" function (a Touchpad Menu Mode selection) is enabled, and normally causes all zones to give a two second beep at the keypad/
Touchpad(s) when any zone is faulted or restored. As required by SIA CP-01, Fault Find is expanded with the following features when
Digital Dialer Report Enter/Exit Test Mode is programmed. This option is programmed when "Enable CP-01 Feature" is selected in
the Easy Menu Driven Program Mode:
•
When Fault Find is entered, it reports to Central Station that "Test Mode" is in progress. On completion of the report, a Ring-
Back will be given.
•
Fault Find can not be initiated from an armed panel, and all digital dialer reporting is inhibited while in Fault Find.
•
Touchpad will display the following warning that the system is in Fault Find: "FAULT FIND RF SIG POWER - - "
•
If 24-hour zone is open at end of test, no report is sent (F-64 panel). If a 24-hour zone is tripped and not restored during Fault
Find, when the mode is exited the zone will display as "Faulted" on the Touchpad/keypad display.
•
When Fault Find is exited by pressing RESET, a Fault Find Restore Report will be sent, and upon completion of the report a
Ring-Back will be given.
Digital Dialer Test
A Digital Dialer Test (Central Station Communication Test) can be initiated from the Touchpad Menu Mode. Press MENU until
Glo
ssar
y