Roland VIMA JM-5 - Manual (Page 12)

JM-5 MIDI Implementation
12
❍ Patch Part parameters
The JM-5 has 19 Parts: 3 parts assigned to External In, and 16 parts for Songs.
For External part control, use the address [50 xx xx]
For Song part control, use the address [40 xx xx]
The 19 Parts are:
The relation between Part number and Block number is as follows.
In the following map, the control numbers of the control changes are indicated as CC#.
External In parts Song parts
Track Name MIDI channel Track Name MIDI channel SysEx X=
1 Tone 1 1 1 Part 1 1 X= 1
2 Tone 2 2 2 Part 2 2 X= 2
3 Tone 3 3 3 Part 3 3 X= 3
4 — — 4 Part 4 4 X= 4
5 — — 5 Part 5 5 X= 5
6 — — 6 Part 6 6 X= 6
7 — — 7 Part 7 7 X= 7
8 — — 8 Part 8 8 X= 8
9 — — 9 Part 9 9 X= 9
10 — — 10 Part 10 10 X= 0
11 — — 11 Part 11 11 X= A
12 — — 12 Part 12 12 X= B
13 — — 13 Part 13 13 X= C
14 — — 14 Part 14 14 X= D
15 15 Part 15 15 X= E
16 — — 16 Part 16 16 X= F
x...BLOCK NUMBER (0~F) Part 1 (default MIDIch = 1) x=1
Part 2 (default MIDIch = 2) x=2
: : :
Part 9 (default MIDIch = 9) x=9
Part10 (default MIDIch =10) x=0
Part11 (default MIDIch =11) x=A
Part12 (default MIDIch =12) x=B
: : :
Part16 (default MIDIch =16) x=F
• n... MIDI channel number (0~F) of the BLOCK.
Address(H) Size(H) Data (H) Parameter Description Default Value (H) Description
40 1x 00 00 00 02 00~7F TONE NUMBER CC#00 VALUE 0~127 00 0
40 1x 01# 00~7F P.C. VALUE 1~128 00 1
40 1x 02 00 00 01 00~10 Rx. CHANNEL 1~16, OFF Same as the Part Number
40 1x 03 00 00 01 00~01 Rx. PITCH BEND OFF/ON 01 ON
40 1x 04 00 00 01 00~01 Rx. CH PRESSURE (CAf) OFF/ON 01 ON
40 1x 05 00 00 01 00~01 Rx. PROGRAM CHANGE OFF/ON 01 ON
40 1x 06 00 00 01 00~01 Rx. CONTROL CHANGE OFF/ON 01 ON
40 1x 07 00 00 01 00~01 Rx. POLY PRESSURE(PAf) OFF/ON 01 ON
40 1x 08 00 00 01 00~01 Rx. NOTE MESSAGE OFF/ON 01 ON
40 1x 09 00 00 01 00~01 Rx. RPN OFF/ON 01 ON
40 1x 0A 00 00 01 00~01 Rx. NRPN OFF/ON 00 (01*) OFF (ON*)
40 1x 0B 00 00 01 00~01 Rx. MODULATION OFF/ON 01 ON
40 1x 0C 00 00 01 00~01 Rx. VOLUME OFF/ON 01 ON
40 1x 0D 00 00 01 00~01 Rx. PANPOT OFF/ON 01 ON
40 1x 0E 00 00 01 00~01 Rx. EXPRESSION OFF/ON 01 ON
40 1x 0F 00 00 01 00~01 Rx. HOLD1 OFF/ON 01 ON
40 1x 10 00 00 01 00~01 Rx. PORTAMENTO OFF/ON 01 ON
40 1x 11 00 00 01 00~01 Rx. SOSTENUTO OFF/ON 01 ON
40 1x 12 00 00 01 00~01 Rx. SOFT OFF/ON 01 ON
40 1x 13 00 00 01 00~01 MONO/POLY MODE Mono/Poly 01 Poly
(=CC# 126 01/CC# 127 00)
40 1x 15 00 00 01 00~02 USE FOR RHYTHM PART 0 = OFF
1 = MAP1
2 = MAP2 00 atı 0
01 at x=0 OFF (Normal Part)
MAP1 (Drum Part)
• This parameter sets the Drum Map of the Part used as the Drum Part. The JM-5 can simultaneously (in different Parts) use up to two Drum Maps (MAP1,
MAP2). With the initial settings, Part10 (MIDI CH=10, x=0) is set to MAP1 (1), and other Parts are set to normal instrumental Parts (OFF(0)).
• Only for Song parts.
Address(H) Size(H) Data (H) Parameter Description Default Value (H) Description
40 1x 16 00 00 01 28~58 PITCH KEY SHIFT -24~+24 [semitones] 40 0 [semitones]
40 1x 17 00 00 02 08~F8 PITCH OFFSET FINE -12.0~+12.0 [Hz] 08 00 0 [Hz]
40 1x 18# Use nibblized data.
• PITCH OFFSET FINE allows you to alter, by a specified frequency amount, the pitch at which notes will sound. This parameter differs from the conventional
Fine Tuning (RPN #1) parameter in that the amount of frequency alteration (in Hertz) will be identical no matter which note is played. When a multiple number
of Parts, each of which has been given a different setting for PITCH OFFSET FINE, are sounded by means of an identical note number, you can obtain a
Celeste effect.
• Only for Song parts.
40 1x 19 00 00 01 00~7F PART LEVEL 0~127 64 100
(=CC# 7)
40 1x 1A 00 00 01 00~7F VELOCITY SENSE DEPTH 0~127 40 64
40 1x 1B 00 00 01 00~7F VELOCITY SENSE OFFSET 0~127 40 64
40 1x 1C 00 00 01 00~7F PART PANPOT -64 (Left)~+63 (Right) 40 0 (CENTER)
40 1x 1D 00 00 01 00~7F KEYBOARD RANGE LOW (C-1)~(G9) 00 C-1