Roland VIMA JM-5 - Manual (Page 3)

JM-5 MIDI Implementation
3
❍ RPN MSB/LSB (Controller number 101, 100)
• Not received when "RPN" RX Event is Off.
• The value specified by RPN will not be reset even by messages such as
Program Change or Reset All Controller.
**RPN**
The RPN (Registered Parameter Number) messages are expanded control
changes, and each function of an RPN is described by the MIDI Standard.
To use these messages, you must first use RPN (Controller number 101 and
100, their order does not matter) to specify the parameter to be controlled, and
then use Data Entry messages (Controller number 6, 38) to specify the value
of the specified parameter. Once an RPN parameter has been specified, all
Data Entry messages received on that channel will modify the value of that
parameter.
To prevent accidents, it is recommended that you set RPN to Null (RPN Num-
ber= 7FH 7FH) when you have finished setting the value of the desired param-
eter.
On the JM-5, RPN can be used to modify the following parameters.
● Program Change
• Not received when “Program Change” RX Event is Off.
• After a Program Change message is received, the sound will change
beginning with the next Note-on. Voices already sounding when the Pro-
gram Change message was received will not be affected.
● Channel Pressure
• Not received when “Channel Pressure” RX Event is Off.
• The resulting effect is determined by System Exclusive messages. With
the initial settings there will be no effect.
● Pitch Bend Change
• Not received when “Pitch Bender ” RX Event is Off.
• The resulting effect is determined by System Exclusive messages. With
the initial settings the effect is Pitch Bend.
■ Channel Mode Messages
● All Sounds Off (Controller number 120)
• When the message is received, all notes currently sounding on the corre-
sponding channel will be turned Off.
● Reset All Controllers (Controller number 121)
• When this message is received, the following controllers will be set to
their reset values.
01H 21H mmH TVF Resonance (relative change)
mm: 00H~40H~7FH (-64~0~+63)
01H 63H mmH TVF&TVA Envelope Attack Time (rel. change)
mm: 00H~40H~7FH (-64~0~+63)
01H 64H mmH TVF&TVA Envelope Decay Time (rel. change)
mm: 00H~40H~7FH (-64~0~+63)
01H 66H mmH TVF&TVA Env. Release Time (relative change)
mm: 00H~40H~7FH (-64~0~+63)
18H rrH mmH Drum Instrument Pitch Coarse (relative change)
rr: Drum Instrument note number
mm: 00H~40H~7FH (-64~0~+63 semitone)
1AH rrH mmH Drum Instrument TVA Level (absolute change)
rr: Drum Instrument note number
mm: 00H~7FH (0~max)
1CH rrH mmH Drum Instrument Panpot (absolute change)
rr: Drum Instrument note number
mm: 00H, 01H~40H~7FH (random, left~center~
right)
1DH rrH mmH Drum Instr. Reverb Send (absolute change)
rr: Drum Instrument note number
mm: 00H~7FH (0~max)
1EH rrH mmH Drum Instr. Chorus Send (absolute change)
rr: Drum Instrument note number
mm: 00H~7FH (0~max)
60H rrH mmH Equalizer Switch
rr: Drum Instrument note number
mm: 00H~02H (Global, Instrument, Off)
61H rrH mmH Equalizer Low Frequency
rr: Drum Instrument note number
mm: 00H~05H (90, 150, 180, 300, 360, 600Hz)
62H rrH mmH Equalizer Low Gain
rr: Drum Instrument note number
mm: 00H~1EH (–15~0~+15dB)
63H rrH mmH Equalizer Mid Frequency
rr: Drum Instrument note number
mm: 00H~10H (200, 250, 315, 400, 500, 630,
800, 1000, 1250, 1600, 2000, 2500, 3150, 4000,
5000, 6300, 8000Hz)
64H rrH mmH Equalizer Mid Gain
rr: Drum Instrument note number
mm: 00H~1EH (–15~0~+15dB)
65H rrH mmH Equalizer Mid Gain
rr: Drum Instrument note number
mm: 00H~04H (0.5, 1.0, 2.0, 4.0, 8.0)
66H rrH mmH Equalizer High Frequency
rr: Drum Instrument note number
mm: 00H~06H (1500, 2000, 3000, 4000, 6000,
8000, 12000Hz)
67H rrH mmH Equalizer High Gain
rr: Drum Instrument note number
mm: 00H~1EH (–15~0~+15dB)
4FH 10H mmH Part 1 On / Off
mm: 00H~7FH (00-3FH=Off - 40-7FH= On)
4FH 11H mmH Part 3 On / Off
mm: 00H~7FH (00-3FH=Off - 40-7FH= On)
4FH 13H mmH Part 2 On / Off
mm: 00H~7FH (00-3FH=Off - 40-7FH= On)
4FH 21H mmH Master Volume Part 1-2 On / Off
mm: 00H~7FH (00-3FH=Off - 40-7FH= On)
4FH 22H mmH Master Volume Part 3 On / Off
mm: 00H~7FH (00-3FH=Off - 40-7FH= On)
Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n= MIDI channel number: 0H~FH (Ch.1~16)
mm= upper byte (MSB)of parameter number specified by RPN
ll= lower byte (LSB) of parameter number specified by RPN
RPN Data entry
MSB LSB MSB LSB Explanation
00H 00H mmH —- Pitch Bend Sensitivity
mm: 00H~18H (0~24 semitones)
Initial value= 02H (2 semitones)
ll: ignored (processed as 00H)
Up to 2 octaves can be specified in semi-
tone steps.
00H 01H mmH llH Channel Fine Tuning
mm, ll: 00 00H~40 00H~7F 7FH (–100~0~
+99.99 cents),
Initial value= 40 00H (+/- 0 cent)
Refer to “About the Tuning” on page 15.
00H 02H mmH —- Master Coarse Tuning
mm: 28H~40H~58H (-24~0~+24 semi-
tones),
Initial value= 40H (+/-0 semitone)
ll: ignored (processed as 00H)
00H 05H mmH llH Modulation Depth Range
mm: 00H~04H (0~4 semitones)
ll: 00H~7FH (0~100 cents) 100/128 Cent/
Value
7FH 7FH —- —- RPN null
Set condition where RPN and NRPN are
unspecified. The data entry messages after
set RPN null will be ignored. (No Data entry
messages are required after RPN null).
Settings already made will not change.
mm, ll: ignored
Status 2nd byte
CnH ppH
n= MIDI channel number: 0H~FH (Ch.1~16)
pp= Program number: 00H~7FH (prog.1~prog.128)
Status 2nd byte
DnH vvH
n= MIDI channel number: 0H~FH (Ch.1~16)
vv= Channel Pressure: 00H~7FH (0~127)
Status 2nd byte 3rd byte
EnH llH mmH
n= MIDI channel number: 0H~FH (Ch.1~16)
mm, ll= Pitch Bend value: 00 00H~40 00H~7F 7FH (–8192~0~+8191)
Status 2nd byte 3rd byte
BnH 78H 00H
n= MIDI channel number: 0H~FH (Ch.1~16)
Status 2nd byte 3rd byte
BnH 79H 00H
n= MIDI channel number: 0H~FH (Ch.1~16)
Controller Reset value
Pitch Bend Change +/-0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)