ROTEL RT-06 - Manual (Page 9)

99 English
OFF Button
Remote only
Pressing the OFF button places the RT-06 into
standby mode. Power is still supplied to the
unit, but functions are disabled.
Remote Sensor
This front panel sensor receives infrared sig-
nals from the remote control. Make sure you
do not accidentally block this sensor with
cables or accessories.
Front Panel Display
The large fluorescent display in the center por-
tion of the RT-06 provides status information
used in operating the DAB/AM/FM receiver
(such as station frequency display, band pre-
set memory, RDS information, etc.)
MEMORY Button
The MEMORY button is used to confirm and
memorize the various setting in the setup and
operation of the RT-06, including tuner sta-
tion presets. Its use is described in detail in
the relevant sections below.
ENTER Button
Pressing the ENTER button selects the high-
lighted parameter in the SETUP display.
SETUP Button
Opens and closes the RT-06 setup menu.
This provides the RT-06 setup menus as well
as the ability to change county modes by
using the front panel ENTER, UP/DOWN
Buttons.
DIMMER Button
Available on the front panel and remote con-
trol, this button selects four display brightness
settings. Press the button to cycle through the
four settings.
NOTE
: When the tuner is turned off then back
on, the display reverts to its normal setting.
The dimmer setting is also available in the
SETUP menu for memory setup until the AC
line is disconnected.
Basic Tuning Controls
The RT-06 features a digital synthesized AM/
FM tuner with RDS or RBDS capability, 30-sta-
tion preset and a DAB tuner with a maximum
of 99 station presets.
• Manual frequency tuning lets you
tune up or down to the next station fre-
quency. Set the TUNE/PRESET mode to
TUNE. Turn off AUTO TUNING. Use the
TUNING controls to tune up or down.
• Direct frequency tuning lets you enter
the desired station frequency digits. Press
the FREQUENCY DIRECT button on the
remote or front panel and enter the digits
using the NUMERIC buttons.
• Automatic frequency search tun-
ing lets you search up or down to find
the next available broadcast signal. Set
the TUNE/PRESET mode to TUNE. Turn
on AUTO TUNING. Use the TUNING
controls to search up or down.
• Memory station preset tuning lets
you directly enter the number of a mem-
orized station preset number. Enter the
number of the memorized preset using
the NUMERIC buttons for the AM/FM or
DAB band.
• Preset scan tuning lets you scan up/
down through the memorized station
presets. Press the PRESET SCAN button
to begin scanning the AM/FM bands.
• RDS (Europe) or RBDS (USA) tun-
ing provides a range of special tuning
and search features based on data codes
encoded with the broadcast signal. See
the RDS section of this manual for detailed
information.
TUNING Controls
A pair of buttons, labeled <TUNING> on the
front panel, and the “FREQ UP/DOWN” and
“PRESET UP/DOWN” buttons on the remote,
serve as the main tuning controls for the RT-
06. You can use either the front panel or re-
mote buttons; their function is identical. These
controls provide different tuning functions de-
pending on the mode of operation.
BAND Button
The BAND button selects whether the tuner
will receive DAB, AM or FM broadcast sig-
nals. Press the button to toggle back and forth
between DAB, AM and FM. A corresponding
indicator will light at the left portion of the
front panel DISPLAY to confirm your choice.
The currently tuned station frequency will
be shown.
FREQUENCY TUNING mode
• With AUTO TUNING off, press a TUN-
ING button to manually jump to the next
frequency, regardless of whether or not a
station is broadcasting on that frequency.
[See the TUNE/PRESET button and AUTO
TUNING button sections for details on
changing the tuning modes.]
• With AUTO TUNING on, press a TUN-
ING button to start auto tuning. The tuner
begins automatically scanning up or down
through the frequencies until the next re-
ceivable signal is detected. If this is not
the desired station, repeat the automatic
tuning procedure to find the next station.
Weak stations will be skipped during auto
tuning. If no receivable signal is detected,
the tuner will revert to the last previously
tuned station. [See the TUNE/PRESET but-
ton and AUTO TUNING button sections for
details on changing the tuning modes.]
PRESET TUNING mode
Press a TUNING button to advance to the
next memorized station preset. [See the
TUNE/PRESET button section for details on
changing the tuning modes.]
RDS PTY search mode
Press a TUNING button to select the desired
program type from the scrolling list in the
display. See the section on RDS tuning for
more details. [See the RDS PTY button sec-
tion for details.]
NOTE
: Several indicators in the front panel dis-
play assist tuning. A large display shows the
tuned frequency and increases or decreases
during tuning. A signal strength indicator
shows the strength of an incoming signal. A
TUNED indicator lights when a sufficiently
strong signal is received. A ST indicator lights
when a stereo FM signal is received. In ad-
dition, indicators show the currently selected
tuning mode.