Radio Shack Dual Keypad - Manual (Page 19)

19 Operation
Storing a Number in the Base
Follow these steps to store numbers in the
base:
1. Hold down MEMORY until
Ijeh[ Ijeh[ Ijeh[ Ijeh[ DkcX[h DkcX[h DkcX[h DkcX[h
appears on the base's display.
2. Enter the phone number and any tone or
pause entries (see “Entering a Pause”).
If you make a mistake, press MEMORY
to exit the memory store operation. Start
again at Step 1.
3. Press MEMORY again.
I[b[Yj I[b[Yj I[b[Yj I[b[Yj BeYWj_ed BeYWj_ed BeYWj_ed BeYWj_ed
appears. Enter the memory location
number (
0 – 9 ) where you want to store
the number. The phone beeps and
C[cehod C[cehod C[cehod C[cehod IIIIjeh[Z jeh[Z jeh[Z jeh[Z
appears.
To clear a stored number, simply store a new
number in its place. Or, hold down
MEMORY
until
Ijeh[ Ijeh[ Ijeh[ Ijeh[ DkcX[h DkcX[h DkcX[h DkcX[h
appears. Then press MEM-
ORY and the memory location number ( 0 – 9 )
you want to clear. The phone beeps and
C[cehodd C[cehodd C[cehodd C[cehodd :[b[j[Z :[b[j[Z :[b[j[Z :[b[j[Z
appears.
Use the supplied memory directory sticker to
record your stored numbers. Peel the back-
ing from the sticker and attach it to the base.
Editing or Deleting a Number in
the Handset's Memory
Follow these steps to edit or delete a memo-
ry number.
1. Lift the handset.
2. Hold down MEM until
C[ceho C[ceho C[ceho C[ceho Ijeh[ Ijeh[ Ijeh[ Ijeh[
and a
list of memory location numbers appear.
3. Choose a memory location ( 01 – 20 ) by
pressing a number or by repeatedly
pressing
VOL/CID
8 8 8 8
or
9 9 9 9
.
4. Press SELECT/INTCM . A menu appears
with the three options listed below.
Press
VOL/CID
8 8 8 8
or
9 9 9 9
to highlight the
desired option then press SELECT/
INTCM to choose it.
Menu Options:
•
;Z_jý C[cehodd ;Z_jý C[cehodd ;Z_jý C[cehodd ;Z_jý C[cehodd
— edit the record as
described in Steps 5 through 8 of “Stor-
ing a Name and Number in the Hand-
set’s Memory” on Page 17.
•
:[b[j[ýC[cehodd :[b[j[ýC[cehodd :[b[j[ýC[cehodd :[b[j[ýC[cehodd
— the display prompts
you to confirm the deletion. Move the
cursor to
O[i O[i O[i O[i
, then press SELECT/INTCM
or DELETE/CH . The phone beeps, and
C[cehodd C[cehodd C[cehodd C[cehodd :[b[j[Z :[b[j[Z :[b[j[Z :[b[j[Z
appears.
•
=eý8WYa =eý8WYa =eý8WYa =eý8WYa
— returns you to the list of mem-
ory numbers.
Entering a Pause
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an out-
side number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to con-
nect.
To enter a 2-second pause, press REDIAL/
PAUSE ( PAUSE on the handset).
FFFF
appears
when you enter a pause in the memory. You
can add more pause entries for a longer
pause.