Onkyo TX-SR502 - Manual (Page 31)

31
Turning On
Notes: (not for the American model)
• The AV Receiver is shipped with the POWER switch
in the ON position ( ). When the power cord is con-
nected for the very first time, the AV Receiver will
enter Standby and the STANDBY indicator will light
up.
• To completely shutdown the AV Receiver, set the
POWER switch to the OFF position ( ).
First Time Setup
To enjoy Dolby Digital and DTS, you must connect your
DVD player to the AV Receiver by using a digital audio
connection (coaxial or optical).
With this function you can assign digital audio inputs to
input sources. You only need to change these assign-
ments if your connections don’t match the default
assignments listed below.
For example, if you connect your DVD player to the
COAXIAL DIGITAL IN, you’ll need to change the
DVD input source from OPT 1 to COAX, and change the
CD input source to something other than COAX.
If you want to use the TAPE input source with only the
analog TAPE IN sockets, you’ll need to change the
TAPE assignment from “OPT3” to “----” (Analog).
You can change the assignments as follows.
Turning On the AV Receiver
1 Set the [POWER] switch to the
ON position (
). (Skip this step if
you have American model.)
The AV Receiver enters Standby mode,
and the STANDBY indicator comes on.
Note:
• The remote controller has no effect
while the [POWER] switch in the
OFF position.
2 Press the [STANDBY/ON] button.
Alternatively, press the remote
controller’s [AMP] button fol-
lowed by the [ON] button.
The AV Receiver comes on, the display
lights up, and the STANDBY indicator
goes off.
To turn off the AV Receiver, press the
[STANDBY/ON] button. The AV
Receiver will enter Standby mode. To
prevent any loud surprises the next time
you turn on your AV Receiver, always
turn down the volume before turning it
off.
CD
+10 0 CLEAR
1 2 3
4 5 6
7 8 9
V1 V2 V3
DVD MULTI CH
--/---
TAPE TUNER
INPUT I
+
-
AMP + _ TONE TUNER/
TAPE
ON STANDBY T V
TV CH
T V VOL
REMOTE MODE
STANDBY/ON
PHONES
SPEAKERS B A
STANDBY/ON
POWER
PHONES
OFF ON
SPEAKERS B A
STANDBY/ON STANDBY/ON
POWER
STANDBY
ON
• American
model
• Other
models
POWER
OFF ON
STANDBY/ON
STANDBY
ON
Remote
controller
Assigning the Digital Inputs to Input
Sources
Input source DIGITAL INPUT
DVD OPT1 (OPTICAL 1)
VIDEO 1 - - - - (Analog)
VIDEO 2 OPT2 (OPTICAL 2)
VIDEO 3 - - - - (Analog)
TAPE OPT3 (OPTICAL 3)
CD COAX (COAXIAL)
1 Press the input selector button
for the source that you want to
assign.
(Digital inputs cannot be assigned to
the TUNER input source.)
2 Press the [DIGITAL INPUT]
button.
The current assignment appears.
3 Press the [DIGITAL INPUT] but-
ton repeatedly to select COAX,
OPT1, OPT2, OPT3, or – – – –.
STANDBY/ON
PHONES
STANDBY
DISPLAY TONE TUNING MODE DIGITAL INPUT LISTENING MODE STEREO MEMORY
RETURN SETUP
VIDEO 2 TAPE TUNER C D VIDEO 3 DVD VIDEO 1
VCR
MULTI CH
MASTER VOLUME
TUNING
ENTER PRESET
S VIDEO VIDEO AUDIO L R VIDEO 3 INPUT CLEAR
SPEAKERS B A
DIGITAL INPUT
Input selector buttons
VIDEO 2
TAPE C D
VIDEO 3
DVD VIDEO 1
VCR
DIGITAL INPUT
DIGITAL INPUT