Onkyo TX-SR502 - Manual (Page 44)

44
Using the Listening Modes —Continued
If the Surr Back setting is set to anything other than None
in the Speaker Configuration (page 32), and if the sur-
round information in the current input signal is “
3/2.1 ”
or “ 3/3.1 (you can check the format of a digital input sig-
nal on page 35, “Displaying Source Information.”), you
can determine whether Dolby Digital and DTS material
is played using 6.1-channels or 5.1-channels.
Dolby Digital Setting
Auto: If the source signal contains a Dolby Digital
EX flag, Dolby Digital EX 6.1 is used. If not,
Dolby Digital 5.1 is used.
On: Dolby Digital EX 6.1 is used regardless of
whether the source signal contains a Dolby
Digital EX flag. You can switch between Dolby
Digital EX and PL IIx Music.
Off: Dolby Digital 5.1 is used even if a Dolby Dig-
ital EX flag is present.
DTS Setting
Auto: If the source signal contains a DTS-ES flag,
DTS-ES Discrete (6.1) or DTS-ES Matrix
(6.1) is selected automatically. If not, DTS 5.1
is used.
On: DTS-ES 6.1 is used regardless of whether the
source signal contains a DTS-ES flag. If the
source signal contains a DTS-ES flag, DTS-ES
Discrete (6.1) or DTS-ES Matrix (6.1) is
selected automatically. If the source signal
does not contain a DTS-ES flag, you can select
DTS+Dolby EX, PL IIx Music, or
DTS+Neo:6.
Off: DTS 5.1 is used for all DTS sources, even if a
DTS-ES flag is present.
Dolby Digital/DTS setting
(5.1 or 6.1-channel playback)
1 Press the [AMP] mode button fol-
lowed by the [SETUP] button.
2 Use the Up and Down [ ]/[ ]
buttons to select “4. Audio
Adjust,” and then press the
[ENTER] button.
CD
+10 0 CLEAR
1 2 3
4 5 6
7 8 9
V1 V2 V3
DVD MULTI CH
--/---
TAPE TUNER
INPUT I
+
-
ENTER
SET UP
GUI DE
RE TURN
EXIT
CINE FLTR
LEVEL - LEVEL + CH SEL TEST TONE
DSP DIRECT
STEREO ALL ST SURR
L NIGHT
TO P M ENU MEN U
VOL
+
-
CDR
SAT
AMP + _
TV VCR CABLE
DVD CD MD
DISC
CH
TONE
TUNER/
TAPE
DISPLAY
TV
INPUT
PREV
CH
DIMMER SLEEP
RANDOM SP A SP B
MUTING
ANGLE
SEARCH
SUBTITLE AUDIO
MEMORY A-B REPEAT
ON STANDBY T V
TV CH
T V VOL
RC-567M
REC
LAST M
REMOTE MODE
OPEN/CLOSE
DSP
VIDEO OFF
LEVEL - LEVEL +
SETUP
AMP
ENTER
SURR
AMP
ENTER
ENTER
3 When playing Dolby Digital
material:
Use the Up and Down [ ]/[ ]
buttons to select “SB (Dolby D),”
and then use the Left and Right
[
]/[ ] buttons to select “Auto,”
“On,” or “Off.”
When playing DTS material:
Use the Up and Down [ ]/[ ]
buttons to select “SB (DTS),” and
then use the Left and Right [
]/
[ ] buttons to select “Auto,”
“On” or “Off.”
4 Press the [SETUP] button.
Setup closes.
5 Use the remote controller’s
[SURR] button, or the AV
Receiver’s LISTENING MODE
[
]/[ ] buttons to select the
required listening mode.
ENTER
ENTER
SURR