Onkyo TX-SR601E - Manual (Page 33)

33
Configuring the speakers
Each speaker can be set between 1 and 30 feet (0.3 and 9 meters) in
1-foot (0.3 meter) increments. Select the setting closest to the actual
distance from the speaker to your normal listening position.
Note:
Speakers that you selected “No” or “None” for in the “Speaker
Config” menu will be disabled.
TX-SR701/701E
Notes:
• For the front L/R, center and subwoofer speakers, the speaker
distance values you can set will be between the current
maximum value(s) among all speakers and the values 10 feet (3
meters) lower than the current maximum value(s). For example,
if the current maximum value is 30 feet (9 meters), the speaker
distance values you can set will be between 20 feet (6 meters)
and 30 feet (9 meters).
• For the surround and surround back speakers, the speaker
distance values you can set will be between the current
maximum value(s) among all speakers and the values 20 feet (6
meters) lower than the current maximum value(s).
• Whenever you set the speaker distance value for any one of the
speakers, if you enter any values higher than the current
maximum value, the value you enter will be the new maximum
value and any other speaker distance values you already set will
automatically be adjusted to the values so that they keep the
same value difference to the new maximum value as the one to
the last maximum value.
1. Use the and cursor buttons to
select “3. Speaker Distance” on the
main menu and then press the
ENTER button.
The “Speaker Distance” menu appears.
2. Use the and cursor buttons to select “Unit” and
then use the and cursor buttons to select the
desired unit of measure.
feet: Select if you will enter the distances in feet.
meters: Select if you will enter the distances in meters.
3. Use the and cursor buttons to select “Left” and
then use the and cursor buttons to set the
distance from the front left speaker to your normal
listening position.
Setting the speaker distance from your normal
listening position
* Menu *****************
1.Hardware Config
2.Speaker Config
3.Speaker Distance
4.Level Calibration
5.Input Setup
6.Preference
|ENTER|Quit:|SETUP|
* Menu *****************
1.Speaker Config
2.Speaker Distance
3.Level Calibration
4.Input Setup
5.OSD Setup
6.Preference
3.Speaker Distance
***********************
a.Unit :feet
b.Left :12ft
c.Center :12ft
d.Right :12ft
e.Surr Right : 7ft
f.Surround Back : 7ft
g.Surr Left : 7ft
h.Subwoofer : 7ft
Quit:|SETUP|
4. Use the and cursor buttons to select “Center” and
then use the and cursor buttons to set the distance
from the center speaker to your normal listening position.
5. Use the and cursor buttons to select “Right” and
then use the and cursor buttons to set the
distance from the front right speaker to your normal
listening position.
6. Use the and cursor buttons to select “Surr Right”
and then use the and cursor buttons to set the
distance from the surround right speaker to your
normal listening position.
7. Do the following when you use two surround back
speakers. If you use one surround back speaker, go to
step 8.
Use the and cursor buttons to select “Surround
Back R” and then use the and cursor buttons to
set the distance from the surround back right speaker
to your normal listening position.
8. When you use one surround back speaker:
Use the and cursor buttons to select “Surround
Back” and then use the and cursor buttons to set
the distance from the surround back speaker to your
normal listening position.
When you use two surround back speakers:
Use the and cursor buttons to select “Surround
Back L” and then use the and cursor buttons to
set the distance from the surround back left speaker
to your normal listening position.
9. Use the and cursor buttons to select “Surr Left”
and then use the and cursor buttons to set the
distance from the surround left speaker to your
normal listening position.
10. Use the and cursor buttons to select “Subwoofer”
and then use the and cursor buttons to set the
distance from the subwoofer speaker to your normal
listening position.
Press the RETURN button to return to the main menu.
Press the SETUP button on the front panel or SETUP button on the
remote controller button to exit the Setup menu.