Onkyo TX-SR601E - Manual (Page 44)

44
Selecting an Audio Component
STANDBY/ON
PHONES VIDEO 4 INPUT
DIGITAL
VIDEO 3 TAPE VIDEO 4
SURROUND THX DSP STEREO
STANDBY
DISPLAY
VIDEO 2 DVD VIDEO 1 AUDIO SELECTOR
LISTENING MODE
MASTER VOLUME RETURN
ENTER
AUDIO ADJUST SETUP
RT/PTY/TP
VCR 2 VCR 1 S VIDEO VIDEO AUDIO L R
OFF ON
POWER
TUNER CD PHONO DIRECT/ PURE AUDIO
PURE AUDIO
REC OUT ZONE 2 OFF LEVEL MEMORY
CLEAR
FM MODE
PRESET
TUNI NG
AUDIO ADJUST
AUDIO SELECTOR PHONES
AUDIO ADJUST
AUDIO SEL
MASTER VOLUME
VOL
SLEEP
STANDBY/ON
PHONES VIDEO 4 INPUT
DIGITAL
VIDEO 3 TAPE VIDEO 4
SURROUND THX DSP STEREO
STANDBY
DISPLAY
VIDEO 2 DVD VIDEO 1 AUDIO SELECTOR
LISTENING MODE
MASTER VOLUME RETURN
ENTER
AUDIO ADJUST SETUP
RT/PTY/TP
VCR 2 VCR 1 S VIDEO VIDEO AUDIO L R
OFF ON
POWER
TUNER CD PHONO DIRECT/ PURE AUDIO
PURE AUDIO
REC OUT ZONE 2 OFF LEVEL MEMORY
CLEAR
FM MODE
PRESET
TUNI NG
AUDIO ADJUST
AUDIO SELECTOR PHONES
AUDIO ADJUST
AUDIO SEL
MASTER VOLUME
VOL
SLEEP
The SLEEP button enables you to set the TX-SR701/701E/601/
601E to turn off automatically after a specified time period. If you
press it once, the TX-SR701/701E/601/601E will turn off after 90
minutes. Each time it is pressed thereafter, this remaining time until
the TX-SR701/701E/601/601E turns off decreases by 10 minutes
(i.e., from 90 to 80 minutes). While the sleep function is enabled,
you can press the SLEEP button to see how much time is left. If the
SLEEP button is pressed when the time displayed is less than 10
minutes, the sleep function is cancelled.
If you are using the remote zone (Zone 2), it will turn off at the
same time as the main zone. If you want to set the sleep function for
Zone 2 only, set the sleep function with the main zone turned on and
then put the main zone into the standby state.
To listen with headphones, plug a pair of headphones with a
standard stereo plug into the PHONES jack on the TX-SR701/
701E/601/601E front panel.
When you connect the headphones, the TX-SR701/701E/601/601E
will enter the STEREO mode automatically and no sound will be
heard from the speakers. When the headphones are unplugged, the
TX-SR701/701E/601/601E returns to its original listening mode.
When using the headphones, you can only use the Direct, Stereo,
and Pure Audio (TX-SR701/701E only) listening modes. If you
have selected multichannel audio, you will only hear the sound
output to the front right and left channels.
The headphone volume level can be adjusted at the Setup Menu (see
page 56).
Note:
The signal to the remote zone (Zone 2) will not be affected by
whether or not headphones are connected.
Using the sleep time (remote controller only)
Listening with headphones
Remote controller
PHONES DIRECT PURE AUD
1. Press the DVD input source button.
2. Select “Multich” using the AUDIO SELECTOR button
on the front panel (or AUDIO SEL button on the
remote controller).
3. Turn on the connected DVD player and start playing
the desired media.
4. If necessary, adjust the output level of each speaker
as desired (see page 43).
Adjust the volume at each speaker so that all the volumes sound
at the same level at the listening position. For the front right,
front left, center, surround right, and surround left speakers, the
output levels can be adjusted between –12 and +12 decibels.
The subwoofer can be adjusted between –30 and +12 decibels.
5. Adjust the volume with the MASTER VOLUME dial or
the VOL buttons on the remote controller.
Enjoying DVD multichannel audio playback
AUDIO
SELECTOR
Remote controller TX-SR701/701E/601/601E