Speaker setup, See “analog audio input, See “subwoofer input – Onkyo TX-NR3008 User Manual

Page 50: Sensitivity, Tings in “speaker settings, Speaker settings” for more, Digital audio input

Advertising

Digital Audio Input

If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPT 1” to the “TV/CD” input selector.
Here are the default assignments.

■

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE,
TV/CD, PHONO, PORT

COAX 1, COAX 2, COAX 3, OPT 1, OPT 2,
OPT 3 (TX-NR5008):

Select a corresponding digital audio input that the
component has been connected.

- - - - -:

Select if the component is connected to an analog
audio input.

• “AUX” is used only for input from the front panel.

Note

• When an HDMI IN is assigned to an input selector in “HDMI

Input” (

➔

48), the same HDMI IN will be set as a priority in this

assignment. In this case, if you want to use the coaxial or optical
audio input, make the selection in the “Audio Selector” in the
Home menu (

➔

68).

• Available sampling rate for PCM signals from a digital input

(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• “TUNER” selector cannot be assigned and is fixed at the

“- - - - -” option.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to “PORT” selector.

Analog Audio Input

If you connect a component to the AV receiver’s analog
multichannel input, you must assign that input to an input
selector. For example, if you connect your Blu-ray Disc/
DVD player to the MULTI CH input, you must assign it to
the “BD/DVD” input selector.

■

Multich

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,
TAPE, TV/CD, PHONO

You can assign the multichannel input to the input
selectors.

- - - - -:

If you don’t want to assign the multichannel input,
set to “- - - - -”.

Note

• To listen to the component connected to the multichannel input,

make the selection in the “Audio Selector” in the Home menu
(

➔

68).

■

Subwoofer Input Sensitivity

0dB to 15dB in 5 dB step.

Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player.

Note

• This setting only affects signals connected to the AV receiver’s

multichannel input SUBWOOFER jack.

• If you find that your subwoofer is too loud, try the 10 dB or

15 dB setting.

Main menu

Speaker Setup

Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup, or set them manually, which is useful if you change
one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup.
Press RECEIVER and use SP LAYOUT on the remote
controller to select Speakers A or Speakers B.

Note

• These settings are disabled when:

– a pair of headphones is connected, or
– the “Audio TV Out” setting is set to “On” (

➔

64) and an

input selector other than HDMI is selected.

Speaker Settings

If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
To use bi-amping or bridging, you must change the
“Speakers Type(Front A)” or “Speakers Type(Front
B)” setting (

➔

51). For details on speaker wire connec-

tion, see “Connecting the AV Receiver” (

➔

17 to 19).

Note

• When bridging is used, the AV receiver is able to drive up to 7.2

speakers in the main room.

• When bi-amping is used, the AV receiver is able to drive up to

7.2 speakers in the main room.

• Before you change these settings, turn down the volume.

Input selector