TVS electronic MINI THERMAL RP-3180 - Manual (Page 11)

[Details] If the values of m is out of the specified range, n1 and data
following are processed as normal data.
The n1 and n2 indicate the number of dots of the bit image in the
horizontal direction.
The number of dots is calculated by n1 + n2 x 256.
If the bit-image data input exceeds the number of dots to be
printed on a line, the excess data is ignored.
d indicates the bit-image data. Set a corresponding bit to 1 to print
a dot or to 0 to not print a dot.
After printing a bit image, the printer returns to normal data
processing mode.
This command is not affected by print modes (emphasized,
double-strike, underline,character size or white/black reverse
printing), except upside-down printing mode.
ESC 2
[Name]
[Format]
[Description]
[Details]
[See Also]
Select default line spacing
ASCII ESC 2
Hex 1B 32
Decimal 27 50
Selects approximately 4.23 mm {1/6"}spacing.
The line spacing can be set independently in standard mode and in
page mode.
ESC 3
ESC 3 n
[Name]
[Format]
[Range]
[Description]
[Details]
[Default]
[See Also]
Set line spacing
ASCII ESC 3 n
Hex 1B 33 n
Decimal 27 51 n
0
n 255
Sets the line spacing to [n x vertical or horizontal motion unit].
The line spacing can be set independently in standard mode and in
page mode.
In standard mode, the vertical motion unit (y) is used.
The maximum paper feed amount is 1016 mm {40"}. Even if a paper
feed amount of
more than 1016 mm {40"}is set, the printer feeds the paper only
1016 mm {40"}.
Approx 4.23mm {1/6"}.
ESC 2
15
ESC 9 m n 1 n2
[Name]
[Format]
[Range]
[Description]
Generating the specified pulses
ASCII ESC 9 m n1 n2
Hex 1B 39 m n1 n2
Decimal 27 57 m n1 n2
m = 0, 0
n1 255 , 0 n2 255
The signals specified by n1 and n2 are output to the connector
pin specified by m .
ESC @
[Name]
[Format]
[Description]
[Details]
Initialize printer
ASCII ESC @
Hex 1B 40
Decimal 27 64
Clears the data in the print buffer and resets the printer mode to the
mode that was in effect when the power was turned on.
The data in the receive buffer is not cleared.
The macro definition is not cleared.
The NV bit image data is not cleared.
The data of the NV user memory is not cleared.
ESC A n
[Name]
[Format]
[Range]
[Description]
[Details]
[Default]
[See Also]
Set line spacing
ASCII ESC A n
Hex 1B 41 n
Decimal 27 65 n
0
n 255
Sets the line spacing to [n x vertical or horizontal motion unit].
The line spacing can be set independently in standard mode and in
page mode.
In standard mode, the vertical motion unit (y) is used.
The maximum paper feed amount is 1016 mm {40"}. Even if a
paper feed amount of more than 1016 mm {40"}is set, the printer
feeds the paper only 1016 mm {40"}.
Approx 4.23mm {1/6"}.
ESC 2
ESC D
[Name]
[Format]
[Description]
Select character Double-height mode
ASCII ESC D
Hex 1B 44
Decimal 27 68
Select character Double-height mode.
16 RP-3180 USER'S MANUAL RP-3180 USER'S MANUAL