Transition Networks CETTF10XX-105 - Manual (Page 2)

Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the 4-position switch and the jumper and when
installing the media converter. Failure to observe this caution could result in
damage to, and subsequent failure of, the media converter.
Set the 4-Position Switch
• The 4-position switch is
located on the media
converter circuit board.
• Use a small flat-blade
screwdriver to set the
switches (see the drawing).
NOTE: When the fiber port or the copper port is disabled (switches 1 and 2),
network traffic coming into the media converter is ignored and no traffic flows
out. In this mode, the media converter is disconnected from the network.
1. Fiber Port (10Base-FL)
Up Enable network traffic on the fiber port.
Down Disable network traffic on the fiber port.
2. Copper Port (10Base-T)
Up Enable network traffic on the copper port.
Down Disable network traffic on the copper port.
3. AutoCross
Up Enable AutoCross (see page 6).
Down Disable AutoCross.
(When AutoCross is disabled, the 10Base-T (copper) port is in
MDI-X (crossover) mode.)
4. Link Pass-Through
Up Enable Link Pass-Through (see page 6).
Down Disable Link Pass-Through.
(When Link Pass-Through is disabled, remote faults are not passed
along to any downstream equipment.)
Set the Hardware/Software Jumper
The hardware/software jumper is located on the media converter circuit
board. Use small needle-nosed pliers or a similar device to set the jumper.
Hardware The media converter mode is determined
by the 4-position switch settings.
Software The media converter mode is determined
by the most-recently saved, on-board
microprocessor settings.
CETTF10xx-105
2 24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Software Mode
Hardware Mode
H S
H S
Fiber Port; up = Enable
Copper Port; up = Enable
Link Pass Through;
up = Enable
AutoCross; up = Enable
1 2 3 4
3 [email protected] -- Click the “Transition Now” link for a live Web chat.
Installation
-- Continued
Install the Slide-in-Module
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing the CETTF10xx-105 slide-in-module media
converter. Failure to observe this caution could result in damage to, and
subsequent failure of, the media converter.
1. Carefully slide the slide-in-module into the installation slot, aligning the
module with the installation guides.
2. Ensure that the module is firmly seated inside the chassis.
3. Push in and rotate the attached panel fastener screw clockwise to secure
the module to the chassis front.
Connect the Twisted-Pair Copper Cable
NOTE: The AutoCross feature allows either MDI (straight-through) or MDI-X
(crossover) cable connections to be configured automatically, according to the
network conditions.
1. Locate or build 10Base-T copper cables with male, RJ-45 connectors
installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the CETTF10xx-105 media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
CFMFF100 CFMFF100 CETCF100 CFETF100 CFETF110 CFMFF100
SPD PWR
FRX
CRX
FLNK
CLNK
10/100TX
RX
TX
10/100SX
100BASE-TX
RX
TX 100BASE-FX
Link Alert E D
0 50½
LA PWR
RXF
RXC COL
LKS PWR
LKM
10BASE-2
10BASE-FL
LKS PWR
LKM
LKS PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
I 0
TERM INIT
RX
TX
LNK
PWR
CPSMM120
SERIAL
10BASE-T
R
E
S
E
T
I 0
RX
TX
Panel Fastener Screw
PWR
RXF LKF
RXC LKC
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter