Toshiba RD-XV47KE - Manual (Page 105)

105 EN
In
troducti
on
Connecti
o
ns
Bas
ic Setup
P
layback
Ed
iti
n
g
V
CR Fu
ncti
on
s
Ot
hers
Fu
nc
ti
on
Set
u
p
Recordi
n
g
T
Symptom Solution
POWER
The power does not turn on. • Check that the AC power cord is connected securely.
• Batteries of the remote control are weak.
The unit turns on automatically without any
operation.
• The unit turns on automatically 2 minutes before the Timer Recording.
The OSD Language Menu appears every
time the power turns on. • Finish up the Language Setting procedure by selecting a language in the
OSD Language Menu. Press [ENTER] to activate the setting.
The power turns off automatically. • The power turns off automatically when abnormality is detected on the
disc. Press [ ON / STANDBY] or [OPEN / CLOSE O] on the unit to
open the disc tray, and before it is opened completely, press the button
again. Then take out the disc.
• The power turns off automatically when an OTR is completed.
Symptom Solution
GEN
E
RAL
The unit does not function. • “ ” or error message appears if the operation is prohibited.
• Batteries of the remote control are weak or exhausted.
No picture, sound or menu appears on the
screen. • Check if the connections are made securely and correctly.
• Check if the cables are damaged.
• Check if a correct external input channel is selected on your TV. (See
page 25.)
• Check if you have completed the Channel Setting. (See pages 27 to 30.)
Clock Setting and Channel Setting cannot be
performed.
• If a recording is in progress, these operations cannot be performed.
The unit does not operate properly. • Moisture has condensed inside the unit. Remove the disc and leave the
unit turned on for about two hours until the moisture evaporates. (See
page 3.)
Symptom Solution
CHA
NNEL
TV channels cannot be changed. • Check if the connections are made securely and correctly.
• Check if the cables are damaged.
• Try Channel Setting by following the steps on pages 27 to 30.
Only specific channels do not appear. • The channels may be set to be skipped. (See page 28.)
The external input channels (such as AV1,
AV2 or AV3) cannot be skipped. • This unit does not skip the external input channels. This is not a
malfunction.
Symptom Solution
RECORDING
G
E
NE
RA
L The image from the external device
cannot be displayed or recorded.
• Try pressing [INPUT SELECT ] repeatedly.
• Turn on all connected devices.
• Check if the connections are made securely and correctly.
HDD/D
V
D
Recording is impossible. • This unit cannot record programmes that contain copy protection signal.
This is not a malfunction.
• The space of the recording media may be used up. Try deleting
unnecessary titles from the Original, or exchange it with the recordable
media.
• The maximum number of titles or chapters has exceeded.
Delete the unnecessary titles to make enough space or insert a new
recordable media.
• Check if the connections are made securely and correctly.
Timer Recording cannot be performed. • The internal clock of the unit may have been stopped due to a power
failure that lasted for more than 30 seconds. Reset the clock. (See pages
30 to 31.)
DVD
Recording is impossible. • Copy-once programmes can only be recorded on a CPRM compatible
VR mode DVD-RW.
• Check if the disc is protected or finalised. Undo the protection or the
finalisation.
• DVD-RW once formatted with other DVD recorders cannot be recorded
on this unit. This is not a malfunction.
• Video mode DVDs recorded by other DVD recorders cannot be used on
this unit unless finalised.
• Check if the connections are made securely and correctly.
VCR
Recording is impossible. • Check if a videotape is inserted.
• Check if a videotape has a record tab intact.
E3B90ED_EN.book Page 105 Friday, February 23, 2007 12:38 PM