Velux DK-2950 - Manual (Page 8)

ENGLISH
3
Operation of several windows:
Operation of window operator, blind or roller shutter on one
specific window
Press “M” to select window operator (M1), blind or roller
shutter (M2 or M3).
Press / to select the window.
Press ▲ open/up, ● stop, ▼ close/down.
The illustration shows the operation of M3 in window no. 2
(in the example M3 is a blind).
Operation of all window operators, blinds or roller shutters
on all windows
Press “M” to select window operator (M1), blind or roller
shutter (M2 or M3).
Press “ALL” to select all windows.
Press ▲ open/up, ● stop, ▼ close/down.
The illustration shows the operation of M3 in all windows
(in the example M3 is a blind).
Setting of operation mode:
The set of four switches in the remote control can be set for
operation in two different ways
If a switch (1, 2 or 3) is set in position "AUTO" (automatic),
the corresponding motor will travel to the end-stop after one
press of the button. If a switch is set in position "MAN"
(manual), the motor will run only as long as the button is
pressed.
"AUTO/MAN" can be set individually for each motor.
The examples at the foot of the page show which switch
belongs to which motor.
Where there is a risk of personal injury, eg in children's
rooms, the switches should be set in position "MAN".
Switch no. 4 must always be in position “ON”.
Setting the security code:
Setting your personal security code (set of ten switches): Set
the same security code in the infra-red receiver and remote
control, but do not set the code shown. Do not set all
switches in position "OFF".
IMPORTANT: The same security code must be used for all
VELUX products in the whole house. It is recommended to
change the security code from time to time.
Emergency operation of the window:
Stop button
By pressing the stop button on the infra-red receiver, the win-
dow operator is stopped immediately.
ENGLISH
Fitting the infra-red receiver:
Fit the infra-red receiver as shown, if this has not already
been done.
Remote control:
Batteries
Fit the batteries supplied (type 1.5 volt AAA) in the remote
control as shown. If display shows “LOW BAT”, please
change the batteries.
Use of remote control
1 :“M”: Selects motor type (window operator, blind or roller
shutter).
2 :“ALL”: Selects all windows.
3 : / : Selects a specific window.
4 : Display shows the selected motor type and window.
5 : ▲ open/up, ● stop, ▼ close/down.
Remote control holder
Fit remote control holder to wall. The remote control can be
fixed in the holder by means of the top bracket.
IMPORTANT: If you choose to fix the remote control in the
holder, make sure that transmission from the remote control to
the infra-red receiver is not inhibited.
Operation of one window:
Operation of window operator
Press “M” to select window operator (M1).
Press “ALL”.
Press ▲ open, ● stop, ▼ close.
Operation of window operator, blind and roller shutter
Press “M” to select window operator (M1), blind or roller
shutter (M2 or M3).
Press “ALL”.
Press ▲ open/up, ● stop, ▼ close/down.
The illustration shows the operation of M3 (in the example
M3 is a blind)
Numbering of the windows:
Give the windows numbers in the order from 1-10 so that
they can be operated separately. Each individual window is
given a number by positioning the code switch in the infra-
red receiver to the desired number. The number of the win-
dow corresponds to the number in the remote control display,
which is selected by pressing / .
2
A
B
C
1
2
3
A
B
4
5
A
B
6
7
A
8