Waterford Appliances E65-NG1 - Manual (Page 32)

32 Waterford E65-1 Emerald Direct Vent Freestanding Gas Stove
FAN MAINTENANCE
If your fan requires maintenance or replace-
ment, access to the fan is through the rear
access panel on the back of the unit. NOTE: the
unit MUST NOT be operated without the
fan access panel securely in place and
correctly sealed.
IMPORTANT: These fans collect a lot of
dust from within your home. Ensure you
maintain these fan motors on a regular
basis by vacuuming out the fan squirrel
cages, around the motor, and around the
grills on the back of the stove.
GENERAL VENT
MAINTENANCE
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or streaks,
and in extreme cases, holes. These com-
ponents should be replaced immediately.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
3) Check for evidences of excessive conden-
sation, such as water droplets forming in
the inner liner, and subsequently dripping
out the joints, Continuous condensation
can cause corrosion of caps, pipe, and
fittings. It may be caused by having exces-
sive lateral runs, too many elbows, and
exterior portions of the system being ex-
posed to cold weather.
4) Inspect joints, to verify that no pipe sections
or fittings have been disturbed, and conse-
quently loosened. Also check mechanical
supports such as Wall Straps, or plumbers'
tape for rigidity.
The nut that holds the
front door is accessible
through the cut-out in
the right side heat
shield.
MAINTENANCE
Top View of pilot flame
Top View of pilot flame
Incorrect flame pattern will have small, probably
yellow flames, not coming into proper contact
with the rear of the burner or thermopile.
across the rear of the burner (it does not
have to be touching the burner).
Note: If you have an incorrect flame pat-
tern, contact your Waterford deal-
er for further instructions.
LOG REPLACEMENT
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the
logs. The pilot light generates enough heat to
burn someone. If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagram under Log
Installation.
Note: Improper positioning of logs may
create carbon build-up and will
alter the unit’s performance which
is not covered under warranty.
GLASS
REPLACEMENT
Your EMERALD stove is supplied with high
temperature, 5 mm Neoceram ceramic glass
that will withstand the highest heat that your
unit will produce. In the event that you break
your glass by impact, purchase your replace-
ment door from an authorized Waterford dealer
only, and follow our step-by-step instructions
for replacement.
1) Open the front door. Open the right side
door and there is a cutout in the heat shield
through which can be seen a 1/4" nut
threaded on to a stud attached to the front
door. Loosen this nut by turning it counter-
clockwise with a 7/16" wrench until it can
be removed by hand.
2) Remove the six screws that secure the
retainers holding the glass in place.
3) Remove the glass and replace with the
new glass.
4) Install two bottom retainers and turn the
screws in just enough to support the glass.
5) Install the other retainers, tighten the screws
alternately. Do not overtighten as this can
damage the glass.
6) Close the door. Thread the nut onto the end
of the stud.
Replacement Part # 940-087 Emerald Glass
WARNING: Do not operate appli-
ance with glass panels removed,
cracked or broken. Replacement of
the glass should be done by a li-
censed or qualified service person.
Note: Wearing gloves will protect your
hands while handling glass.
REPLACING
THE GASKET
The Emerald has 3/8" fiberglass gasket in the
front door. Should it ever need replacement,
use only the proper replacement gasket that is
available from your Waterford dealer. To re-
place the gasket, follow this procedure.
1) Open the front door (see instructions above
in Glass Replacement 1).
2) Remove the existing gasket and clean its
channel with a scraper or wire brush.
3) Lay a thin bead of gasket cement the entire
length of the channel.
4) Lay the gasket in the channel with suffi-
cient pressure that it stays in place. Trim the
excess from the end of the gasket so that
it butts snugly against the other end without
leaving a gap.
5) Close the door and apply firm pressure to
seat the gasket evenly throughout.
WARNING:
Electrical Grounding Instructions
This appliance is equipped with a
three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.