Wayne-Dalton TORQUEMASTER 3663-372 - Manual (Page 16)

9 Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need.
You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com
Cable Dru m
No space betwe
e Pawl and Ca b ind icates eng a
Ca Ratchet Pawl
EN GA GED SID E VIE W
No space between Ratchet Pawl and Cable Drum
ENG AGED U NDE RNE ATH VIE W
Space betwee n R and Cable non-indicates e
Ratchet Pawl
DISENGAGED SIDE
VIEW
No space between Ratchet Pawl and
DISENGAGED U
NDE RNE ATH V IEW
UPPER POSITION
LO WER POSITION
L
UPPER POSITION SIDE VIEW Ratchet Paw l in Lower P
Ratchet Pawl in Upper Position
Use these Illustration,
in conjunction with the Instructions on the o
t
this labe l. WARNING WAR
NING Rachet Bracket is under Rac het Bra cke t is u nde r
EXTREME SPRING EXTR EME SPR ING TENSION TEN SION .
To avoid possible severe or To a void po ssib le s eve re o r
fatal injury
,
fata l inju ry, DO NOT DO N OT remove rem ove
fasteners from ratchet bracket fast ene rs fr om ratc het bra cke t
until spring(s) are fully until sp ring (s) a re fu lly
wnwound. wnw oun d.
To safely unwind spring(s) To s afe ly u nw ind sp ring (s)
read rea d
and follow the directions in the and follo w th e d irec tion s in the
installation instructions/owners insta llatio n in stru ctio ns/o wne rs
manual. ma nua l.
DO NOT REMOVE THIS T
AG.
DO N OT R EMO VE T HIS T AG.
Cable Dru m
No s pace between Ratche t Pawl and Cable Dru m ind icates engagement
Cable Drum Ratc het Pa wl
EN GAGED SIDE VIEW
No space between Ratchet Pawl and Cab le Drum
ENGAGED U NDE RNE ATH VIEW
Space between R atch et Paw l and C able Dru m non- indicate s engagement
Cable Drum Ratch et Pawl
DISEN GAGED SIDE VIEW
No sp ace betw een Ratch et Paw l and
DISENGAGED U NDE RNE ATH VIEW
UPP ER POS ITION
LOW ER PO SITI ON
LO WER POSI TION S IDE V
UPPER POSITION SIDE VIEW Rat chet Pa wl in Lower Position
Ratchet Pawl in U pper Posi tion
Use these Illus
tration, in conjunction with the Instructions on the other side of this label. WARNING WAR
NING Rachet Bracket is under Rac het Bra cke t is u nde r
EXTREME SPRING EXTR EME SPR ING TENSION TEN SION .
To avoid possible severe or To a void po ssib le s eve re o r
fatal injury
,
fata l inju ry, DO NOT DO N OT remove rem ove
fasteners from ratchet bracket fast ene rs fr om ratc het bra cke t
until spring(s) are fully until sp ring (s) a re fu lly wnwound. wnw oun d.
To safely unwind spring(s) To s afe ly u nw ind sp ring (s) read rea d
and follow the directions in the and follo w th e d irec tion s in the
installation instructions/owners insta llatio n in stru ctio ns/o wne rs
manual. ma nua l.
DO NOT REMOVE THIS T
AG.
DO N OT R EMO VE T HIS T AG.
IMPORTANT! WARNING TAGS MUST BE
SECURELY ATTACHED TO BOTH END
BRACKETS.
End brackets are right and left hand. You
can identify the right hand end bracket by
the disconnect cable guide hole in the top
of the bracket.
Beginning with either side, slide the end
bracket onto the winding shaft so that the
grooves in the ratchet wheel fit onto the
winding shaft splines.
Secure end bracket to the flag angle using
(1) 5/16”-18 x 3/4” carriage bolt, 3/4”
washer and hex nut; then secure to the
jamb with 5/16” x 1-5/8” hex head lag
screw.
Repeat for other end bracket.
NOTE: No ratchet wheel is required on the
left hand side for single spring applications.
Only an end bracket is needed.
After completing this step, continue with
Step 4 on page 12.
Splines
Winding
Shaft
Groove
Disconnect Cable
Guide Hole
Right End
Bracket
Warning Tag
Right End
Bracket
Ratchet
Wheel
Teeth Pointing
Upward
3
End Brackets
No space between Ratchet Pawl and Cable Drum indicates engagement
Cable Drum Ratchet Pawl
ENGAGED SIDE VIEW
No space between Ratchet Pawl and
Cable Drum
ENGAGED U NDE RN EAT H V IEW
C Ratche t Pa
DISENGAGED SIDE VIEW
DISENGAGED U
NDE RNE ATH V IEW
Use these Illustration,
in conjunction with the Instructions on the other sid
e
this label. WARNING WAR
NING Rachet Bracket is under Rac het Bra cke t is u nde r
EXTREME SPRING EXTR
EME SPR ING
TENSION TEN SION .
To avoid possible severe or To a void po ssib le s eve re o r
fatal injury
,
fata l inju ry, DO NOT DO N OT remove rem ove
fasteners from ratchet bracket fast ene rs fr om ratc het bra cke t
until spring(s) are fully until sp ring (s) a re fu lly
wnwound. wnw oun d.
To safely unwind spring(s) To s afe ly u nw ind sp ring (s)
read rea d
and follow the directions in the and follo w th e d irec tion s in the
installation instructions/owners insta llatio n in stru ctio ns/o wne rs
manual. ma nua l.
DO NOT REMOVE THIS T
AG.
DO N OT R EMO VE T HIS T AG.
5/16” x 1-5/8”
Hex Head Lag
End Bracket
(Right Hand)
5/16”-18 Hex
Nut
5/16” - 18 X 3/4”
Carriage Bolt
Tools Needed:
Power Drill
7/16” Socket
Driver
1/2” Wrench
Step Ladder
3
Black Tooth
3/4” WASHER