Yamaha S80 EN - Manual (Page 30)

30
Troubleshooting
If you encounter problems such as no sound output or abnormal behavior, verify the connections before
checking the following. If you are using Voice Editor for Windows, refer to the XGworks(lite) owner's
manual too.
<Macintosh>
The printer port is not recognized.
• The printer port will not be recognized if AppleTalk
is ON. Note that with some Macintosh models,
AppleTalk is automatically enabled when starting
up.
• Verify that the “Printer” checkbox has been checked
in the OMS MIDI Setup window.
The modem port is not recognized.
• On some Macintosh models such as the Performa
series, the modem port cannot be used and only the
printer port is available.
• Verify that the “Modem” checkbox has been
checked in the OMS MIDI Setup window.
No MIDI In/Out data
Is the MIDI device’s HOST SELECT switch set correctly?
•
Make the correct setting according to the
instructions in the CS6x/CS6R/S80/S30 Owner's
Manual.
• In the OMS Port Setup, is MIDI In/Out set to
“unknown”? If you change the OMS ports or setup,
the OMS output ports have to be set accordingly in
Voice Editor's OMS Port Setup window. Choose the
appropriate receiving device.
• Is OMS using the same port as that connected to
the cable? Open the OMS MIDI Setup window and
verify that the checkbox for the relevant port has
been checked.
• If the port and setup assignments are frequently
altered, OMS may be unable to easily recognize the
serial port. Reboot the Macintosh, set up OMS
correctly, then start up Voice Editor.
Bulk data are not received.
• Open the OMS Port Setup window and check that
the MIDI In has been properly assigned
(Page 28) .
• Open the Editor Setup Dialog and check that the
Device No. has been properly assigned
(Page 10) .
Voice Editor does not start up when Library File
(extension .S2V) is double-clicked.
• Change the Type/Creator settings for Library Files
as follows, then try double-clicking the file again.
CS6x/CS6R
Type: S2VX
Creator: YXC6
S80/S30
Type: S2VX
Creator: YXS8
<Windows>
Voice Editor is not available in the Plug-in menu.
• Is the Voice Editor installed in the same folder as
XGworks(lite)? If not, reinstall Voice Editor.
Bulk data is not received.
• Is the MIDI In set correctly in the System Setup of
XGworks?
• Open the Editor Setup Dialog and check that the
Device No. has been properly assigned
(Page 10) .
MIDI Out port is not available in Editor Setup.
• The MIDI Out port in Editor Setup can be chosen
from the MIDI Out ports in the System Setup of
XGworks(lite). Check the MIDI Out settings in the
System Setup of XGworks(lite).
<Windows / Macintosh>
Sound does not change when using knobs or
sliders.
• Are the MIDI Out port and Device Number set
correctly in the Editor Setup?
(Page 10)
Bulk data is not transmitted.
• Are the MIDI Out port and Device Number set
correctly in the Editor Setup?
(Page 10)
• Is the Dump Interval in the Editor Setup too
short? Make sure the Dump Interval is at least
10 ms.
Sound is doubled when playing keyboard.
• On your CS6x/CS6R/S80/S30 synthesizer,
switch Local to OFF.
No sound heard when clicking on-screen
keyboard in Edit Window.
• Is the MIDI Ch. set correctly in the Editor
Setup?
(Page 10)
Sound does not change when Monitor button is
pressed.
• Are the MIDI Out port and Device No. set
correctly in the Editor Setup (OMS Port Setup)?
(Pages 10 and 28)
Library files created in Voice Editor cannot be
read directly by CS6x/CS6R/S80/S30.
• Set the file extension to “S2V” in order to read
Voice Editor's Library files directly on your
CS6x/CS6R/S80/S30 synthesizer.