Yamaha HTR-5990 - Manual (Page 84)

80
MANUAL SETUP
Test tone TEST
Turns the test tone output on or off to compare the tonal
quality of the center, surround L/R, surround back L/R,
surround back and presence L/R speakers with that of the
front L/R speakers.
Choices: ON, OFF
■ Low-frequency effect level
B)LFE LEVEL
Use to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer or headphones. The LFE channel carries low-
frequency special effects which are only added to certain
scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Choices: –20 to 0 (dB)
Speaker LFE level SPEAKER
Select to adjust the speaker LFE level.
Headphone LFE level HEADPHONE
Select to adjust the headphone LFE level.
Depending on the settings of LFE LEVEL, some signals may not
be output from the SUBWOOFER PRE OUT jack.
■ Dynamic range
C)DYNAMIC RANGE
Use to select the amount of dynamic range to be applied to
your speakers or headphones. This setting is effective only
when the unit is decoding Dolby Digital and DTS signals.
Choices: MIN (minimum), STD (standard),
MAX (maximum)
Speaker SP
Select to adjust the dynamic range of speakers.
Headphone HP
Select to adjust the dynamic range of headphones.
• Select MIN if you regularly listen at low volume levels.
• Select STD for general use.
• Select MAX to preserve the greatest amount of
dynamic range.
■ Audio set
D)AUDIO SET
Use to customize the overall audio settings for this unit.
Muting type MUTE TYPE
Use to adjust how much the muting function reduces the
sound output.
Choices: FULL, –20 dB
• Select FULL to completely halt all output of sound.
• Select –20 dB to reduce the current volume by 20 dB.
Audio Delay A.DELAY
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 240 (ms)
Tone bypass TONE BYPASS
Use to automatically bypass the tone control when BASS
and TREBLE are set to 0 dB.
Choices: AUTO, OFF
• Select AUTO to automatically bypass the tone control
when BASS and TREBLE are set to 0 dB.
• Select OFF not to bypass the tone control at any time.
■ HDMI set
E)HDMI SET
Use to adjust the HDMI support audio.
Support audio SUPPORT AUDIO
Use to select whether to play back HDMI audio signals on
this unit or on another HDMI component connected to the
HDMI OUT jack on the rear panel of this unit.
Choices: HTR-5990, OTHER
• Select HTR-5990 to play back HDMI audio signals on
this unit. The HDMI audio signals input at the HDMI
IN jacks of this unit are not output to the HDMI
component connected to the HDMI OUT jack on the
rear panel of this unit.
• Select OTHER to play back HDMI audio signals on
another HDMI component.
The HDMI video signals input at the HDMI IN 1 or HDMI IN 2
jack of this unit are always output at the HDMI OUT jack of this
unit.
Note
. SPEAKER;;;;;;0dB
HEADPHONE ;;;;0dB
B)LFE LEVEL
[ ]/[ ]:Up/Down
[<]/[>]:Adjust
p
p
. SP: MIN STD[MAX
HP: MIN STD [MAX
C)DYNAMIC RANGE
[ ]/[ ]:Up/Down
[<]/[>]:Adjust
p
p
Note
. MUTE TYPE;;;FULL
A.DELAY ;;;;;;0ms
TONE BYPASS ;AUTO
LE>E
D)AUDIO SET
[ ]/[ ]:Up/Down
[<]/[>]:Adjust
p
p
[<]/[>]:Adjust
SUPPORT AUDIO:
HTR-5990
E)HDMI SET