Candy CDF8 615 X - S - Manual (Page 12)

23 22
EN 50242 place load
Capacity with pans and dishes
Water supply pressure
Fuse
Power input
Supply voltage 15
9 persons
Min. 0,08 - Max 0,8 MPa
(see rating plate)
(see rating plate)
(see rating plate)
DESCRIPTION OF THE CONTROL PANEL
TECHNICAL DATA:
DIMENSIONS:
Height
Depth
Width
Depth with door open cm
cm
cm
cm
with working top
85
60
60
120
without working top
82
57,3
59,8
117
A "ON/OFF" button
B "PROGRAMME SELECTION" button
C "START"/"RESET" button
(start/cancelling programme)
D "DEGREE OF SOILING" button
("VARIO POWER")
E "ALL in 1" option button
F "DELAY START" button
G "PROGRAMME SELECTION" lights
H "DEGREE OF SOILING" indicator lights
("VARIO POWER")
I "SALT EMPTY" light
L "OPTION SELECTION" light
M "PROGRAMME STATUS" lights/
"DELAY START" time lights
A B C D E F
H I M L G
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
IMPORTANT
The dishwasher has two very practical
functions:
- the "recommended" programme
(which is set in the factory and is
ideal for full-load daily use) for quick
and accurate selection;
- the memory function which saves
the last programme used, so that if
you regularly use the same washing
cycle, you do not have to re-set the
programme every time, thereby
saving time and effort.
"DEGREE OF SOILING" button
(VARIO POWER)
This button offers a choice of three levels of
wash intensity, according to how dirty the
dishes are. The default setting for this
function is the intermediate one (central
indicator light on).
To set the intensity of wash, press the button
to increase (top indicator light) or reduce
(lower indicator light) this will modify the
wash time and the wash temperature.
The combination of 3 different wash intensity
with the four main wash programmes
(indicated on the control panel) enable to
have up to 12 different wash cycles.
IMPORTANTE
When the dishwasher is switched on,
the "DEGREE OF SOILING" last used
will be indicated. If a programme has
been cancelled while in process, the
"DEGREE OF SOILING" setting will
return to intermediate (central indicator
light on).
Programme settings
■ Open the door and place the dirty dishes
inside the appliance.
■ Press the "ON/OFF" button .
The indicator light for the "recommended"
programme or the indicator light for the
last programme used will flash.
■ To set another programme, press the
"PROGRAMME SELECTION" button.
■ If you wish to choose the "DEGREE OF
SOILING", press the corresponding
button.
■ If you wish to select an option, press the
option button (the corresponding indicator
light will light up).
The option button can be selected or
deselected WITHIN one minute of the
programme commencing.
■ Press the "START" button (the selected
programme indicator light will stop
flashing and remain on.
■ When the door is shut, after an audible
signal has sounded, the programme will
start automatically.
WITHIN one minute of the programme
commencing, another programme
can be selected, simply by pressing
the "PROGRAMME SELECTION"
button (it is also possible to change
the "DEGREE OF SOILING" setting,
by pressing the corresponding
button).
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically.
Close the door, without pressing any
buttons
. The cycle will start from where it
left off.
IMPORTANT
A running program can be interrupted
without opening the door by
pressing the "ON/OFF" button. In
this case, simply press the "ON/OFF"
button again to restart the cycle from
where it left off.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.