Speedhut Ford GT Series Gauge - Manual (Page 6)

Over Rev
Red #2
Shift point
Red #1
Brightness LED
Yellow #3
Span LED
Yellow #2
Shift LED
Yellow #1
Select
button
One of the most exciting features of the Ford GT tachometer is the
integrated shift LED's in the dial. This new technology lets you anticipate
the next shift point by displaying 3 yellow warning LED's before reaching
the set shift point Red #1 LED. The span between the LED's can also be
set. Red #2 is an over-shift light that blinks if you exceed the set shift
point by the set span value. If, for any reason you miss a shift and
over-shoot your shift point this light will blink.
The following procedures can be done at any time during operation of the
tachometer while the tachometer has power.
Shift point set
Red #1 is set shift point. The 3 Yellow LEDs will turn on before the set
shift point by the amount of span selected.
1. Press and release the ‘menu’ button until the 'shift point' LED is lit.
2. Press and release the 'select button. The ‘shift point’ LED will blink
once to indicate you have selected the shift point.
3. Set shift point.
Press and hold the 'Select' button to increase RPM shift point.
Press and hold the 'Menu' button to decrease RPM shift point.
After the desired shift point is reached, release the buttons for 2 seconds.
The ‘shift point’ LED will blink 2 times to confirm the new set shift point.
Shift RPM Span set
The shift span is the RPM between the LEDs. (See fig. #6). Setting a
span of '0' RPM will turn on all 5 LEDs at the set shift point. Setting a
maximum span of 400 RPM (see fig. #6) will turn on the next LED after
400 RPM of previous LED.
Example: shift point set at 6500, span set at 200 RPM.
Yellow #1 will light at 5900, Yellow #2 at 6100, Yellow #3 at 6300, Red #1
(shift point) at 6500, finally Red #2 will blink at 6700 RPM.
1. Press and release the ‘menu’ button until the 'span' LED is lit.
2. Press and release the 'select’ button. The ‘span’ LED will blink once to
indicate you have selected the RPM span point.
3. Set RPM span.
Press and hold the 'select' button to increase RPM span.
Press and hold 'Menu' button to decrease RPM span.
After the desired span is reached, release the buttons for 2 seconds. The
‘span’ LED will blink 2 times to confirm the new RPM span.
Note: if you select 0 RPM then all LED's will light at the same time at the
shift point.
0 RPM
50 RPM
100 RPM
150 RPM
200 RPM
(factory default)
250 RPM
300 RPM
350 RPM
400 RPM
Menu
button
Tachometer set shift point.
WARRANTY
Speedhut inc warrants to the consumer for a period of 5 years from the date of purchase that the entire product will be free from defects in materials or
workmanship. Speedhut warrants to the original consumer for a 'LIFETIME' that the gauge circuit board within the gauge housing will be free from defects
in materials and workmanship. Please contact Speedhut service dept if you have a problem with this gauge. [email protected]
Speedhut would like to give a special thank you to ‘mardyn’ on Ford GT forum for helping us greatly with
this project. Also, Cool Tech LLC (www.cooltechllc.com) for helping us with instructions. Thanks guys!
To set the LED brightness, press and release the ‘menu’ button until the ‘LED’ is lit. Press and release the ‘select’ button. Press and
release the ‘select’ button to increase brightness. Press and release the ‘menu’ button to decrease brightness. After a 2 a second delay,
the ‘LED’ will blink to indicate the setting has been saved.
Set your LED brightness for both day and night.