Asus Terminator C3 - Manual (Page 57)

A S U S T e r m i n a t o r T 1 C 3 b a r e b o n e s y s t e m A S U S T e r m i n a t o r T 1 C 3 b a r e b o n e s y s t e m A S U S T e r m i n a t o r T 1 C 3 b a r e b o n e s y s t e m A S U S T e r m i n a t o r T 1 C 3 b a r e b o n e s y s t e m A S U S T e r m i n a t o r T 1 C 3 b a r e b o n e s y s t e m 4 - 7 4 - 7 4 - 7 4 - 7 4 - 7
4 . 4 . 4 . 4 . 4 . A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X + 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X + 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X + 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X + 1 2 V ) A T X p o w e r c o n n e c t o r s ( 2 0 - p i n A T X P W R , 4 - p i n A T X + 1 2 V )
These connectors are for ATX power supply plugs. The plugs from the
power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
Make sure to connect the 4-pin ATX +12V power plug; otherwise, the
system does not boot up.
5 . 5 . 5 . 5 . 5 . F r o n t p a n e l a u d i o c o n n e c t o r ( 5 - 1 p i n M I C _ L O U T ) F r o n t p a n e l a u d i o c o n n e c t o r ( 5 - 1 p i n M I C _ L O U T ) F r o n t p a n e l a u d i o c o n n e c t o r ( 5 - 1 p i n M I C _ L O U T ) F r o n t p a n e l a u d i o c o n n e c t o r ( 5 - 1 p i n M I C _ L O U T ) F r o n t p a n e l a u d i o c o n n e c t o r ( 5 - 1 p i n M I C _ L O U T )
This connector is for a chassis-mounted front panel audio I/O module
that supports legacy AC’97 audio standard.
C3V ®
C3V ATX power connector
+3.3Volts
-12.0Volts
Ground
Power Supply On
Ground
Ground
Ground
-5.0 Volts
+5.0 Volts
+5.0 Volts
Power Good
+12.0Volts
+3.3 Volts
+3.3 Volts
Ground
+5.0 Volts
Ground
+5.0 Volts
Ground
+5V Standby
ATX12V
ATXPWR
+12V DC COM
+12V DC COM
C3V ®
C3V Front panel audio connector
MIC_LOUT
MIC Signal MIC PWR
Head set Left channel
GND Head set Right channel
1