ATI Amplifier Technologies ATP8700 - Manual (Page 16)

DVI/HDMI If the recording device has a DVI or HDMI video
output, and your TV/monitor has a DVI or HDMI input,
connect it to the second DVI input jack on the rear of the
A/V PROCESSOR (ATP8700). For HDMI-equipped video
recorders, use an HDMI-to-DVI adapter.
Analog Audio Connect the L and R audio outputs on the
recorder to any of the audio input jacks on the rear of the A/V
PROCESSOR and connect the L and R inputs of the recorder to
the RECORD OUT audio jacks on the A/V PROCESSOR.
Digital Audio If your recording device also has a digital
audio output jack, connect it one of the coaxial or optical
input jacks on the rear of the A/V PROCESSOR, depending on
the type of connector used by the device. Later, you will
configure the A/V PROCESSOR to use the specific input that
you have chosen. For now, note which digital input you used on
your system chart. If your recording device also has a digital
input jack, connect it to the optical output (DIGITAL OUT) jack
on the rear of the A/V PROCESSOR, depending on the type of
connector used by the device. The signal from the selected digital
input source of the A/V PROCESSOR will be sent to the recorder.
DIGITAL TV TUNER/CABLE BOX/SATELLITE RECEIVER
Composite Connect the composite video output from the TV
tuner/Cable Box/Satellite Receiver to a composite video input
jack on the rear of the A/V PROCESSOR.
S-Video If there is an S-Video output on the TV tuner, and
you have an S-Video input on your TV or monitor, connect it to
an S-Video input jack on the rear of the A/V PROCESSOR.
Analog Audio Connect the L and R channel outputs on the
TV tuner to the analog audio input on the rear of the A/V
PROCESSOR that corresponds to the video input you used.
Digital Audio Connect the digital output jack on the TV
tuner to one of the coaxial or optical input jacks on the rear
of the A/V PROCESSOR, depending on the type of connector
used by the box. Later, you will configure the A/V PROCESSOR
to use the specific digital audio input that you have chosen.
For now, note which digital input you connected to on your
system chart.
Component Video If the TV tuner has a component video
output, and your TV has a component video input, connect
the recording device to one of the component video input
jacks on the rear of the A/V PROCESSOR.
DVI/HDMI If the TV tuner has a DVI or HDMI video output,
and your TV/monitor has a DVI or HDMI input, connect it to
the second DVI input jack on the rear of the A/V PROCESSOR
(ATP8700). For HDMI-equipped DVD players, use an
HDMI-to-DVI adapter.
Video Display Connections
A video display device such as a television, a video monitor or
a video projector can be connected to the A/V PROCESSOR
using the following methods.
Main Zone
Composite Connect the composite video input from the
display to the composite (yellow) VIDEO MONITOR OUT jack
on the rear of the A/V PROCESSOR.
S-Video If there is an S-Video input on the display, connect it
to the S-Video VIDEO MONITOR OUT jack on the rear of the
A/V PROCESSOR.
Component Video If your display has a component video
input, connect it to the component video output jacks on the
rear of the A/V PROCESSOR. You should connect this in
addition to an S-Video or composite video connection.
DVI/HDMI If your video display has a DVI or HDMI video
input, connect it to the DVI output jack on the rear of the
A/V PROCESSOR (ATP8700). If the display has only and HDMI
input, use an HDMI-to-DVI adapter.
Analog Audio If your TV has an internal tuner and offers
an analog audio output for its internal tuner, connect the L&R
channel outputs on the TV to an analog audio input on the
rear of the A/V PROCESSOR.
Digital Audio If your TV tuner has an digital audio output,
connect it to one of the coaxial or optical input jacks on the
rear of the A/V PROCESSOR, depending on the type of
connector used. Note, that with some cable set-top boxes, it is
advisable to make both an analog and digital audio connection.
Later, you will configure the A/V PROCESSOR to use the
specific digital audio input that you have chosen. For now,
note which digital input you used on your system chart.
Page 16