ATI Amplifier Technologies ATP8700 - Manual (Page 28)

Using Preprogrammed Codes
The A/V PROCESSOR remote can be programmed to operate
other audio or video components in your system. The AVC
button is used exclusively for control of the A/V PROCESSOR.
To program the remote to control another device, you must
enter a four-digit code. Codes for a wide variety of devices
and brands are provided in the following pages. More than
one setup code number may work with your device. You
should test the functions for each of the code numbers that
work with your device to determine the best one for your
particular unit.
The procedure for setting up the A/V PROCESSOR remote to
control a TV/VCR is different—see Programming TV/VCR
Control below.
NOTE: Some devices, such as CD players and DVD players
that do not have power buttons on their original remote
controls, may not shut off during programming. For these
devices, it may be necessary to first store the setup code
number and then test functions like PLAY, STOP, etc, to
determine if the correct number has been selected.
To Program Using Four-digit Codes:
1. Turn on the device you would like the remote control to
operate, either manually or with its original remote control.
2. Find the four-digit setup code number for your device from
the tables on pages 29 through 33.
3. On the A/V PROCESSOR remote, press the component key
(near the top of the remote) that corresponds to the device
you want to control.
You can choose from CBL, AUX, VCR, TV, SAT, CD, or AMP.
NOTE: The codes for controlling DVD players are
programmed into the AUX button.
4. Press and hold SETUP on the remote until the red LED at
the top of the remote blinks twice, then release SETUP.
5. Enter the first four-digit code for your component.
The LED should blink twice. If it does not, then repeat
steps 3, 4, and 5 above, using the same code.
6. Aim the remote at the component and press PWR once.
The component should turn off. If it does not respond,
repeat steps 3, 4, and 5, trying each code for your brand
until you find one that works. If it still does not work, try
searching for the code (see Searching For Your Code, below).
7. Repeat the process for other components you wish to
control with the A/V PROCESSOR remote.
PROGRAMMING TV/VCR CONTROL
The A/V PROCESSOR can control TV/VCR combo units, but
the procedure is somewhat different than entering codes to
control other components. As with other components, you
must enter a four-digit code. Codes for many TV/VCR brands
are provided in the following pages. More than one setup
code number may work with your device. You should test the
functions for each of the code numbers that work with your
device to determine the best one for your particular unit.
If you want to control TV functions besides power on/off, you
may need to enter a separate TV code, as described below.
To Program TV/VCR Control:
1. Turn on the TV/VCR, either manually or with its original
remote control, and insert a video cassette.
2. Find the four-digit code for your TV/VCR from the tables
on pages 29 to 33. Your TV/VCR may have a separate TV
code listed. If so, be sure to note both codes.
3. On the A/V PROCESSOR remote, press VCR.
4. Press and hold SETUP until the red LED blinks twice, then
release SETUP.
5. Enter the first four-digit code for your component. If the
code entry is performed correctly, the LED will blink twice.
If it does not, then repeat steps 3, 4, and 5, using the same
four-digit code.
6. Aim the remote at the TV/VCR and press PWR once. The
TV/VCR should turn off. If it does not respond, repeat
steps 3, 4, and 5, trying each code for your brand until you
find one that works. If it still does not work, try searching
for the code (see Searching For Your Code).
7. If your component has a separate TV code listed, press TV
on the A/V PROCESSOR remote. The LED will blink twice.
8. Enter the four-digit TV code for your TV/VCR combo. If the
code is entered correctly, the LED will blink twice. If it does
not, then repeat steps 7 and 8 using the same four-digit code.
SEARCHING FOR YOUR CODE
If your device does not respond to the remote after you have
tried all codes listed for your brand, or if your brand is not
listed at all, try searching for your code.
To Search for a Code for Your Component:
1. On the A/V PROCESSOR remote, press the button near the
top of the remote for the type of device you want to control.
You can choose CBL, AUX, VCR, TV, SAT, CD, or AMP.
2. Press and hold SETUP until the red LED on the remote
blinks twice, then release SETUP.
3. Enter 991. The LED will blink twice.
4. Aim the remote control at the component and slowly
alternate between pressing PWR and the button for the
device you pushed in step 1.
5. Stop when the TV turns off.
6. Press SETUP once.
7. To search for the codes of your other components, repeat
the process, using the appropriate button for the new
device in steps 1 and 4.
Page 28