Fluid Components International FS2000L - Manual (Page 2)

Fluid Components International LLC NuTec ® Series
This page is subject to the proprietary rights statement on the last page
2 Doc. No. 06EN003348 Rev. D
Section B - Instrument Installation
For the FS2000, FS2000H and the LS2000, there is an orientation mark etched onto the sensor element. It is located on a flattened area of
the sensor element body close to the housing.
For the LS2000, the orientation mark can be perpendicular or parallel to the liquid level. The sensor element can be installed top mount 90º to the
liquid surface.
For the FS2000 and the FS2000H, the orientation mark must be parallel to flow, (± 3º). For liquid vertical flows, FCI recommends that the sensor
element be installed where the flow is going in the up direction.
SPECIFICATIONS
Model FS2000 Insertion Flow Switch (I) 3
LS2000 Insertion Level Switch (II) 3
FS2000H Insertion Flow Switch, High Flow Rate (III) 3
FS2000L In-Line Flow Switch, Non-Intrusive (IV) 3
Material of
Construction:
304/305 or 316L Stainless Steel (I & II)
316L Stainless Steel (III & IV)
Operating
Temperature:
Sensor Element: -40° to +250°F [-40° to +121°C]
Control Circuit: -0° to +140°F [-18° to +60°C]
Maximum
Operating
Pressure:
For Process Connections With:
Male NPT/Compression Fitting: 500 psig [35 bar (g)]
Butt Weld: 500 psig [35 bar (g)]
Flanges (Sanitary): 100 psig [ 7 bar (g)] (IV)
Flanges (ANSI): Per Specification (I, II)
Input Power: 24 Vac or Vdc. 3 watts Max.
100 to 240 Vac. 5 watts Max.
2-Wire Loop Power (I, II, IV)
22.5 to 33 Vdc .5 watts Max
Signal
Output:
Available on 24 Volt and 100 to 240 input power units.
Alarm indicator is a 6 amp relay, 28 Vdc / 240 Vdc resistive.
Secondary alarm indicator is an open collector circuit (250
mA Maximum).
FS2000, FS2000H and LS2000 Only 2
2-Wire Loop Power: Alarm indicator responds to change in
current draw between 14 mA and 18 mA.
Installation: Top or Side Mount. Axial flow direction permissible.
Service: General Purpose for Gases and Liquids
Agency
Approvals:
FM, CSA, CE Mark, ATEX, Sanitary 3A, ASME BPE (1997) (IV)
FM, CSA, CE Mark, ATEX, Cenelec (I, II)
FM, CSA, CE Mark, CRN, ATEX 1 (III)
LS2000 Level Switch
Accuracy: Top Mount: ±0.250 inch [±6mm] from element tip
Side Mount: ±0.125 inch [±3mm] from centerline of
element tip
Response
Time:
Dry to Wet: Less than 2 seconds
Wet to Dry: Less than 5 seconds
Wet to Wet: interface: Less than 10 seconds
FS2000 Flow Switch
Setpoint
Range:
Water: 0.1 – 1.5 fps [0.03 – 0.45 mps]
Hydrocarbon: 0.1 – 2.0 fps [0.03 – 0.60 mps]
Air: 0.5 – 100 sfps [0.15 – 30 nmps]
Repeatability: ±1% of Setpoint Range
Response
Time: 0.5 – 2.5 Seconds
FS2000H Flow Switch
Setpoint
Range:
Water: 0.1 – 10 fps [0.03 – 3 mps]
Hydrocarbon: 0.2 – 20 fps [0.06 – 6 mps]
Air: 0.25 – 750 sfps [0.08 – 230 nmps]
Repeatability: ±1% of Setpoint Range
Response
Time: 0.5 – 7 Seconds
FS2000L Flow Switch (Non-Intrusive)
Setpoint
Range:
Water: 0.1 – 10 fps [0.03 – 3 mps]
Air: 0.5 – 300 sfps [0.15 – 91.4 nmps]
Tubing Air / Gas Water
½ inch
1.02 – 13.4 scfm 0.03 – 3.4 gpm
[0.000 – 0.38 scmm] [0.11 – 12.9 lpm]
1 inch
0.12 – 74 scfm 0.18 – 18.5 gpm
[0.0030 – 2.10 scmm] [0.68 – 70 lpm]
2 inch
0.57 – 342 scfm 0.85 – 85.5 gpm
[0.0160 – 9.70 scmm] [3.22 – 324 lpm]
Repeatability: ±1% of Alarm Setpoint
Accuracy: ±3% of Alarm Setpoint ±0.25% of Setpoint Range
Response
Time:
Adjustable from 0.5 – 2.5 Seconds
NOTES:
1. Special Conditions for Safe Use:
2. For applications in explosive atmospheres caused by air/dust mixtures,
cable and conduit entries used shall Customer must provide a 4-20mA
current loop that will maintain 18 to 29.5 volts at the controller control
cuircuit.
3. Roman Numerals reflect model designation.
a. Provisions shall be made to prevent the rated voltage being exceeded
by transient disturbances of more than 40%.
b. For applications in explosive atmospheres caused by air/dust mixtures,
cable and conduit entries used shall provide a degree of ingress
protection of at least IP 54 according to EN 60529.
REF