Clear-Com EF-701M User Manual
Clear-Com Accessories communication
Advertising
Table of contents
Document Outline
- Clear-Com Encore
- EF-701M Interface
- INSTRUCTION MANUAL
- Contents
- OPERATION 1-1
- Installation 2-1
- Connecting the EF-701M Interface 2-1
- Connecting the EF-701M to a Matrix Port 2-1
- Connecting the EF-701M to a Modem 2-2
- Connecting the EF-701M to RTS-TW Equipment 2-5
- Other Connections 2-5
- Levels 2-6
- Nulling 2-7
- Internal Adjustments 2-10
- Transmission methods 2-12
- Direct Connection 2-12
- Fiber-Optic 2-13
- Other Methods 2-15
- Maintenance 3-1
- Glossary 4-1
- Specifications 5-1
- Limited Warranty 6-i
- Warranty Period 6-i
- Technical Support 6-ii
- Warranty Repairs and Returns 6-iii
- Non-Warranty Repairs and Returns 6-iv
- Extended Warranty 6-v
- Liability 6-v
- 1. Read these instructions.
- 2. Keep these instructions.
- 3. Heed all warnings.
- 4. Follow all instructions.
- 5. Do not use this apparatus near water.
- 6. Clean only with dry cloth.
- 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- 9. Only use attachments/accessories specified by the manufacturer.
- 10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- 11. Unplug this apparatus during lightning storms or when unused for long periods of time.
- 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, su...
- 13. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- OPERATION
- Introduction
- Description
- Front Panel Controls
- Figure 1-5: Front panel of an EF-701M unit
- 1. ON- Either a successful data link has been established with a remote EF-701M unit, or the Matrix Direct mode has been selected at the local EF-701M unit.
- 2. OFF- There is no data connection at the local EF-701M unit.
- 3. RAPID BLINK- There is data connection at the local EF-701M unit, but a “break” condition is present. Depending on the modems used, this can indicate a problem at the remote end.
- 4. SLOW BLINK- A test earbud or headphone has been plugged into the test tone jack at the local EF-701M and the nulling test tone is on.
- Rear Panel Settings and Connectors
- Connecting the EF-701M Interface
- Connecting the EF-701M to a Matrix Port
- 1. On the EF-701M’s back panel, set mode-switch 1 to the ON position.
- 2. Connect a CAT-3, CAT-5, or above cable from the RJ-45 Matrix connector on the back panel of the EF-701M to a port (RJ-45) on the Matrix frame.
- 3. Program the Matrix port. Refer to the Eclipse Configuration System (ECS) Manual for instructions.
- Connecting the EF-701M to a Modem
- 1. Connect the local party-line channel to the EF-701M’s rear-panel 3-pin XLR connector.
- 2. Check to see that the EF-701M is receiving power by checking the green Power LED (the “on” light). If there is a powered EF-7...
- 3. Send a call signal and check that it is received at the distant intercom system.
- 4. Adjust nulls, and then check audio levels as required.
- 5. Repeat as necessary for each EF-701M in the system.
- Connecting the EF-701M to RTS-TW Equipment
- Other Connections
- Connecting the EF-701M to a Matrix Port
- Levels
- Nulling
- 1. Connect all the local party-line devices for that channel together and to the EF-701M.
- 2. Plug into the front-panel earphone jack labeled “test.” You will now hear a steady 200-Hz tone through the earphone.
- 3. Adjust the “R” control until the tone is at its minimum.
- 4. Adjust the “L” control until the tone is at its minimum.
- 5. Adjust the “C” control until the tone is at its minimum.
- 6. Because these controls interact with each other, you will need to repeat steps 3, 4, and 5 several times before fully minimizing the test tone.
- 7. Continue these adjustments until the test tone is virtually inaudible.
- 8. Unplug the earphone when the nulling operation is complete.
- Internal Adjustments
- 1. Disconnect all cables.
- 2. Remove the four sheet metal screws on the back and sides.
- 3. The XLR jack has a special locking tab to secure it to the housing. The jack must be released before the cover can be removed...
- 4. Remove the two 3/16 in. hex-head jack screws on the DB-15.
- 5. Slide the cover backwards until the DB-15 and XLR jacks are clear.
- 6. Lift off the cover.
- 7. Make the necessary adjustments of jumpers P3 and P4 (shown in the following table).
- 8. For reassembly, reverse steps 1 through 6.
- Transmission methods
- EF-701M technical Specifications
- Warranty Period
- Technical Support
- Warranty Repairs and Returns
- Non-Warranty Repairs and Returns
- Extended Warranty
- Liability