CNB SKB-21Z12F - Manual (Page 14)

• BACKLIGHT
[ECL(0~100)/WDR(W-REAR,W-MIDDLE,
W FRONT)/ BLC(LOW MIDDLE HIGH)/OFF]
AUTO EXPOSURE SETUP
AE SETUP ▬ GLOBAL
BACKLIGHT OFF ☞
◎ Setup the general functions of zoom camera module.
• FOCUS MODE [AUTO/MANUAL/SEMIAUTO]
S t f d
CAMERA MODULE SETUP
W-FRONT)/ BLC(LOW. MIDDLE, HIGH)/OFF]
- Sets Backlight Compensation
• DAY/NIGHT [AUTO/DAY/NIGHT]
- it excute that change Day&Night in the lower luminance.
BACK
EXIT
DAY /NIGHT
BRIGHTNESS
IRIS
SHUTTER
AGC
3D-DNR
SENS
▬ UP
< AUTO >
50
AUTO
ESC
HIGH
MIDDLE
< AUTO > - Sets camera focus mode.
{ SEMIAUTO Mode
This mode exchanges focus mode automatically
between Manual Focus mode and Auto Focus mode.
Manual Focus mode activates in preset operation and
Auto Focus mode activates when jog operation starts.
With Manual mode at presets, Focus data is memorized
in each preset in advance and camera calls focus data
in correspondence with presets as soon as camera
• BRIGHTNESS [0~100]
- Adjusts brightness of images. Iris, Shutter Speed and Gain are adjusted automatically in
correspondence with this value.
• IRIS [AUTO/MANUAL(0~100)]
If I i i t t A t I i h ld h hi h t i it i dj ti AE d Sh tt S d h ld
in correspondence with presets as soon as camera
arrives at a preset.
• DIGITAL ZOOM [ON/OFF]
- Sets digital zoom function to ON/OFF. If this is set to OFF, optical zoom function runs but
zoom function stops at the end of optical zoom magnification.
• IMAGE FLIP [ON/OFF]
- If IMAGE FLIP is ON, Current image is reversed. If IMAGE FLIP is OFF, Reversed
i ill t i t t - If Iris is set to Auto, Iris should have highest priority in adjusting AE and Shutter Speed should
be fixed. If Iris is set to Manual, Iris should be fixed and Iris has lower priority in adjusting AE,
in comparison with others.
• SHUTTER SPEED [AUTO/A-FLK/MANUAL(x128~1/90000/OFF]
- If Iris is set to MANUAL and Shutter Speed is set to AUTO, Shutter Speed should have
highest priority If Shutter Speed is set to A-FLK to remove Flicker Shutter Speed should be
image will recover to previous status.
◎ Camera zoom settings associated with the module
to perform.
• SHARPNESS LEVEL [0~100]
Adjust the sharpness of the picture
IMAGE ADJUST SETUP
IMAGE ADJUST
SHARPNESS LEVEL
GAMMA MODE 30
CRT ☞
highest priority. If Shutter Speed is set to A FLK, to remove Flicker, Shutter Speed should be
set to 1/100 sec. for NTSC and 1/120 for PAL. If Shutter Mode is set to MANUAL, Shutter
speed is able to adjust from x128 to 1/90000.
• AGC [LOW/MIDDLE/HIGH/OFF]
- Enhances image brightness automatically in case that luminance level of image signal is too
low.
- Adjust the sharpness of the picture.
• GAMMA MODE [CRT/LCD]
- Select the video output mode.
• STABILIZER [ON/OFF]
- Vibration and shaking of the image to compensate.
BACK
STABILIZER
EXIT
OFF
• 3D-DNR [LOW/MIDDLE/HIGH/OFF]
- Enhances images by deducting noises when gain level of images is too high.
• SENS-UP [AUTO(2~128)/OFF]
- Activates Slow Shutter function when luminance of image (signal) is too dark. It is possible to
set up the maximum number of frames piled up one on another by Slow Shutter function
• WHITE BALANCE MODE [ATW/ AWB/ /INDOOR/
OUTDOOR/ MANUAL]
- Red and Blue level can be set up manually.
• RED GAIN [-100~100]
WHITE BALANCE SETUP
WHITE BALANCE SETUP -GLOBAL
WHITE BALANCE MODE
├ RED GAIN
└ BLUE GAIN ATW ☞
26 27
set up the maximum number of frames piled up one on another by Slow Shutter function. • BLUE GAIN [-100~100]
• RED ADJUST [-100~100]
• BLUE ADJUST [-100~100]
BACK
EXIT