Pach and Company AeGIS 4000BP Manual - Manual (Page 29)

CHAPTER 4. OPERA CHAPTER 4. OPERA TIONS TIONS
It is important for you to understand the system’s operations completely for the most ease of operations. You can enable or
disable the system programming remotely via a touch-tone phone or locally via the system’s keypad.
Pach and Company Page 21
AeGIS 4000BP Chapter 4. Operations
TO INITIATE THE CALL AND
DISCONNECT THE CALL FROM
THE AeGIS 4000BP.
ANSWER THE AeGIS 4000BP
CALL AND EXTEND THE TALK
TIME.
PROVIDE ACCESS TO VISITOR.
USING A CALL WAITING
FEATURE.
FUNCTION CODE 96 MUST BE
SET 1-9 RINGS
CALL WAITING WILL NOT
WORK IF FUNCTION CODE IS
DISABLED
USING PERSONAL ACCESS
CODE.
Press # to initiate a call to a premise or remote location, and you will hear:
“A Ring Back “ until the called is answered or the system’s timer is expired (see function
code 92). If you decide to abort the call, press
∗.
Tenant will hear double rings (distinctive ringing) if the AeGIS 4000BP calls to a premise.
No distinctive ringing will be heard if the AeGIS calls to a remote location.
Step 1 Answer the AeGIS calls.
Step 2 Talk to your visitor, you will hear “One Short Beep” 10 seconds before the talk
time expired, press # to extend the talk time to another cycle. Press 9 to provide access
to relay 1 (door1) or press 8 to provide access to relay 2 (door 2) then you will hear
“Two Short Beeps” or hang up if you do not want to provide access to your visitor.
Connection must be established then tenant needs to press 9 to provide access to relay 1
(door 1) or press 8 to provide access to relay 2 (door 2) to visitor and you will hear “Two
Short Beeps”.
The AeGIS 4000BP has built-in call waiting feature. You may not be able to tell the different
between the AeGIS call waiting beeps and the phone company call waiting beeps.
FUNCTION CODE 96 MUST BE SET 1-9 RINGS.
If you are connected to an outside line and receive a call from the AeGIS 4000BP:
Step 1 You will hear “Three Sets of a Short Beep” with three seconds delay between
them (indicates you have an incoming call from the AeGIS 4000BP). Do Not Hang-
up, Doing So Will Disconnect Both Calls.
Step 2 Press ∗∗ to disconnect the outside call and now you are connected to the AeGIS or
Press “0” to put the outside calls on hold and you will hear “Three Sets of Two
Short Beep” with three seconds delay between them (indicates you have a call
holding on the outside line).
Step 3 Press 9 to provide access to relay 1 (door 1) or press 8 to provide access to relay
2 (door 2) to visitor and you will hear “Two Short Beeps” or
∗∗ to hang-up with the
AeGIS and you will be automatically switched to the original call.
If you are connected with the AeGIS 4000BP and receive an outside call:
Step 1 You will hear “Three Sets of Three Short Beeps” with three seconds delay
between them (indicates you have an incoming call from the outside line). Do Not
Hang-up, Doing So Will Disconnect Both Calls.
Step 2 Press 9 to provide access to relay 1 (door 1) or press 8 to provide access to relay
2 (door 2) to visitor and you will hear “Two Short Beeps”. Press
∗∗ to disconnect
the AeGIS calls and you are connected to the out side calls or
Press “0” to put the AeGIS calls on hold and you will hear “Three Sets of a Short
Beep” with three seconds delay between them, indicates you have a call holding.
Press
∗∗ then a 4-digit access code.
• Hear “Two Long Beeps” means your access code is accepted by the system.
• Hear “One Long Beep” means your access code is denied because of invalid or
same code is programmed on Index 01-20, 21-40 or 41-50 and try again.
Do not program the same access code on Index 01-20, Index 21-40 and 41-50,
otherwise the access code will not work.
DESCRIPTION ACTION