Pach and Company AeGIS 4000BP Manual - Manual (Page 30)

ENABLE AND DISABLE CALL
FORWARDING.
ACTIVATE AUTOMATIC CALL
FORWARDING
UNLOCK CYCLE, UNLOCK
HOLD AND LOCK RELAY 1
(DOOR 1) AND RELAY 2 (DOOR
2).
Pach and Company Page 22
AeGIS 4000BP Chapter 4. Operations
Enable and Disable Function Code 70 via system’s keypad
To enable: the call forwarding is automatically enabled if the phone number is programmed
on function code 70 (see Chapter 3).
To disable: Press * and 0 simultaneously, then 0#, you will hear “Three Short Beeps” the
phone number on function code 70 will be deleted.
Enable and Disable Function Code 71 and 72 Call Forwarding via system’s keypad
(Local).
Step 1 Press 0 and ∗ simultaneously then release them.
Step 2 To Enable: Press 1 or 2 (for telephone number stored in function code 71 or 72)
then press #. You will hear “Three Short Beeps”. If the phone number does not
exist you will hear “One Long Beep”.
To disable: Press * and 0 simultaneously, then 0#, you will hear “Three Short
Beeps”.
Step 3 Wait for about 15 seconds before trying to call from the system.
Enable or Disable Function Code 71 and 72 Call Forwarding from Premise Phone.
Step 1 Pick up your handset and wait for a dial tone.
Step 2 Press # # and you will hear “One Short Beep”, then
Step 3 To Enable: Press 1 or 2 (for telephone number stored in function code 71 or 72).
You will hear “Three Short Beeps” and you are disconnected. If the phone number
does not exist, you will hear “One Long Beep”.
To Disable: Press 0, you will hear “Three Short Beeps”.
Enable or Disable Function Code 71 and 72 Call Forwarding from Remote Location.
Step 1 Pick up your handset and wait for a dial tone.
Step 2 Dial the AeGIS phone number and you will hear “One Short Beep” if the gate is
locked or “Two Short Beeps” if the gate is unlocked.
Step 3 Press # then the 4-digit master code, you will hear “One Short Beep” then
Step 4 To Enable: press 1 or 2 (for telephone number stored in function code 71 or 72)
then you will hear “Three Short Beeps” and you are disconnected. If the phone
number does not exist, you will hear “One Long Beep”.
To Disable: Press 0, you will hear “Three Short Beeps”.
There are three different function codes 87, 88, and 89 need to be configured. You can
configure them local or remote, see chapter 3.
• Function Code 87 (Enable or Disable Automatic Call Forwarding) is enabled by default.
• Function Code 88 (Select Automatic Call Forwarding Function Code Number) is selected to
Function Code 71 automatically if a phone number is programmed on 71.
• Function Code 89 (Set Automatic Call Forwarding Time).
Via the System’s Keypad
Note: cannot do unlock cycle from the system’s keypad.
Step 1 Press 0 and # simultaneously then release. If you are in the programming mode,
proceed to step 2.
Step 2 Enter the 4-digit Master Code (factory default is 0000) and you will hear “One
Short Beep”. If you entered an invalid master code you will hear “One Long
Beep”, repeat step 1. Should your master code become lost or forgotten see
Reset Master Code.
Step 3 Enter 90 for relay 1 (door 1) or 91 for relay 2 (door 2) then #, you will hear “One
Short Beep”.
Step 4 Press 1 (to unlock hold) then press #, you will hear “Two Long Beeps” then “One
Short Beep”. If you hear “One Short Beep”, means the door is unlocked or Press
0 (to lock) then press #, you will hear “One Long Beep” then “One Short Beep.
DESCRIPTION ACTION