Alliance Laundry Systems UF35PV - Manual (Page 35)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
33 F232059
Programming Tutorial
The following procedure guides the programmer
through a complete cycle and allows hands-on
experience for programming cycles. The complete
cycle is listed in Table 3.
1. Locate the key-operated programming switch
behind the access door directly below the
emergency stop button (top right on the front
panel of the washer-extractor).
Insert the key and turn the switch to PROGRAM
position. The display will read “CYC00”.
2. Press the Add Cycle key. The display will read
“ACYC00”.
3. A two-digit number from 01 to 39 must be
entered. Cycle number 39 is recommended
because standard program versions use this short
cycle for performing a chemical supply setup.
4. Press key 3, then key 9, then the Enter key. The
display will read “CYC39”.
a. If the display alternately flashes “EXISTS”
and “EDIT?”, press the Clear/Stop key. The
display will return to “CYC39”.
b. Erase the existing cycle: Press the Erase Cycle
key. The display will show “ECYC39”. Press
key 3, then key 9, then the Enter key. The
display will read “WAIT” briefly and then
“CYC39”.
c. Press the Add Cycle key. The display will
read “ACYC39”. Press key 3, then key 9, then
the Enter key. The display will show “0139”.
5. Enter the desired function for step 1. A natural
choice might be hot fill to low level.
a. Press the Hot key and then the Low key. The
display will read “HL0139”.
b. Press the Enter key. The display will read
“M---S”.
c. Now enter the desired fill time. The
recommended number of minutes is four.
Press key 4. The display will read “4M-00S”.
6. Now press the Enter key. The display will read
“0239”, indicating that the computer is ready for
step 2 of cycle 39.
7. A natural choice for step 2 is the addition of a
supply.
a. To add supply No. 1, press the Supply key and
then key 1. The display will read “S10239”.
b. Press the Enter key and the display will read
“M---S”.
c. Now enter the desired time in minutes and
seconds for the supply valve to be turned on.
Thirty seconds is the recommended time.
Press key 0 for minutes, and the display will
read “0M-00S”.
Now press key 3 and then key 0. The display
will read “0M-30S”, indicating a supply time
of thirty seconds.
8. Now press the Enter key. The display will change
to read “0339”, indicating that the computer is
ready for step 3.
9. If no other supply is required, the next step is to
choose the type of wash desired and assign it a
time. For example, one might choose a wash with
standard reversing action (Wash 1) and a time of
six minutes.
a. Press the Wash key and then key 1. The
display will read “W10339”.
b. Press the Enter key. The display will read
“M---S”.
c. Press key 6. The display will read “6M-00S”,
indicating a wash step of six minutes.
10. Press the Enter key. The display will read“0439”,
indicating that the computer is ready for step 4.
11. A drain step usually comes next.
a. Press the Drain key. The display will read
“D-0439”. This program allows a choice
among drains 1, a, or b. For this application,
press key 1. The display will read “D10439”.
b. Then press the Enter key. The display will
read “M---S”.
c. Enter the maximum time desired for the
computer to allow the machine to drain to
empty. The recommended time is one minute.
Press key 1, and the display will change to
“1M-00S”, indicating a drain step of one
minute.